STEVAL-MKI062V2 STMicroelectronics, STEVAL-MKI062V2 Datasheet - Page 7

• Manufacturer Part Number: STEVAL-MKI062V2
• Description: BOARD EVAL FOR MEMS SENSORS
• Manufacturer: STMicroelectronics
• Series: iNEMOr

Specifications of STEVAL-MKI062V2

• Design Resources: STEVAL-MKI062V2 Gerber Files STEVAL-MKI062V2 Schematic STEVAL-MKI062V2 Bill of Materials
• Sensor Type: Accelerometer, Gyroscope, Magnetometer, Pressure, Temperature
• Sensing Range: ±2g,4g,8g; 300 ~ 1100mbar; 300°/sec; -55 ~125°C
• Interface: I²C, USB
• Sensitivity: Multiple
• Voltage - Supply: 5V, USB
• Embedded: Yes, MCU, 32-Bit
• Utilized Ic / Part: LPR430AL, LY330ALH, LSM303DLH, LPS001DL, STM32F103RE, STLM75
• Interface Type: USB, CAN, I2C
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Silicon Manufacturer: STMicroelectronics
• Kit Application Type: Sensor
• Application Sub Type: MEMS Device
• Silicon Family Name: INEMO
• Kit Contents: MicroSD Card Slot, COM Connector, Reset Button,
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: STM32F103RE
• Other names: 497-10508

UM0701
3
General system description
The STM32-MEMS demonstration board serves to connect data and control signals of
a MEMS sensor to pins of the STM32 microcontroller.
The STM32-MEMS board is designed to fit on particular connectors of compatible STM32
demonstration boards. The compatible boards are: STM3210B-EVAL board (with medium-
density STM32 MCU), STM3210E-EVAL board (with high-density STM32 MCU) and
STM3210B-SK/IAR (for medium-density STM32 MCU).
The STM32-MEMS board has a DIL24 socket to connect any STEVAL-MKI0xxVx MEMS
demonstration board compatible with the socket. The recommended boards are: digital
MEMS accelerometers STEVAL-MKI013V1 (LIS302DL) and STEVAL-MKI009V1
(LIS3LV02DL), and analog MEMS accelerometers STEVAL-MKI015V1 (LIS344ALH),
STEVAL-MKI018V1 (LIS244AL) and STEVAL-MKI020V1 (LIS302SG).
The system with STM32-MEMS board offers full control over the MEMS sensor. For analog
sensors all axes, power-down and full-scale signals are available. For digital sensors both
SPI and I
To run the system, the STM32-MEMS board must be connected on one side to an STM32
demonstration board, and on the other side to a MEMS demonstration board. The jumpers
on the STM32-MEMS demonstration board have to be fitted properly. In some cases, minor
changes may have to be made to the STM32 demonstration board. All system settings are
described in detail in the following chapters.
Figure 2.
STM32 demonstration board
2
C interfaces are usable as well as interrupt lines.
System with STM32-MEMS demonstration board
STM32- MEMS board
Doc ID 15703 Rev 1
STEVAL MKI032V1
STM3210B - SK/IAR
MEMS demonstration
STM3210B - EVAL
STM3210E - EVAL
STEVAL - MKI0xxVx
-
board
General system description
AM00446
7/42