ADZS-BF518F-EZLITE Analog Devices Inc, ADZS-BF518F-EZLITE Datasheet - Page 52

• Manufacturer Part Number: ADZS-BF518F-EZLITE
• Description: KIT EZ LITE BF512F/14F/16F/18F
• Manufacturer: Analog Devices Inc
• Type: DSPr

Specifications of ADZS-BF518F-EZLITE

• Featured Product: Blackfin® BF50x Series Processors
• Contents: Board, Cables, CD, Head Phones, Power Supply
• Silicon Manufacturer: Analog Devices
• Core Architecture: Blackfin
• Features: USB-based, PC-hosted Tool Set
• Kit Contents: Brd, PSU, CD, Docs, SD Card, Cables
• Silicon Family Name: Blackfin
• Silicon Core Number: ADSP-BF518F
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: BF512F/14F/16F/18F
• For Use With: ADZS-BFBLUET-EZEXT - EZ-EXTENDER DAUGHTERBOARD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

ADSP-BF512/BF514/BF516/BF518(F)
BF512/BF514/BF516/BF518(F) processor’s output voltage and
the input threshold for the device requiring the hold time. C
the total bus capacitance (per data line), and I
age or three-state current (per data line). The hold time will be
t
Timing Specifications on Page 27
SDRAM write cycle as shown in
Page
Capacitive Loading
Output delays and holds are based on standard capacitive loads:
30 pF on all pins/balls (see
(nominal) = 2.5 V/3.3 V.
Figure 55 on Page 53
capacitance. The delay and hold specifications given should be
derated by a factor derived from these figures. The graphs in
these figures may not be linear outside the ranges shown.
DECAY
V
LOAD
NOTES:
THE WORST CASE TRANSMISSION LINE DELAY IS SHOWN AND CAN BE USED
FOR THE OUTPUT TIMING ANALYSIS TO REFELECT THE TRANSMISSION LINE
EFFECT AND MUST BE CONSIDERED. THE TRANSMISSION LINE (TD), IS FOR
LOAD ONLY AND DOES NOT AFFECT THE DATA SHEET TIMING SPECIFICATIONS.
ANALOG DEVICES RECOMMENDS USING THE IBIS MODEL TIMING FOR A GIVEN
SYSTEM REQUIREMENT. IF NECESSARY, A SYSTEM MAY INCORPORATE
EXTERNAL DRIVERS TO COMPENSATE FOR ANY TIMING DIFFERENCES.
4pF
plus the various output disable times as specified in the
30).
Figure 47. Equivalent Device Loading for AC Measurements
(Includes All Fixtures)
50
70
50
400
2pF
show how output rise time varies with
Figure 48 on Page 52
45
0.5pF
Figure
TESTER PIN ELECTRONICS
SDRAM Interface Timing on
(for example t
47). V
ZO = 50 (impedance)
TD = 4.04
LOAD
T1
is 1.5 V for V
L
1.18 ns
is the total leak-
through
DSDAT
Rev. PrE | Page 52 of 62 | March 2009
for an
OUTPUT
DUT
DDEXT
L
is
Figure 48. Typical Rise and Fall Times (10%–90%) versus Load Capacitance
Figure 49. Typical Rise and Fall Times (10%–90%) versus Load Capacitance
Figure 50. Typical Rise and Fall Times (10%–90%) versus Load Capacitance
TBD
TBD
TBD
Preliminary Technical Data
for Driver A at EVDD
for Driver A at EVDD
for Driver B at EVDD
MAX
MIN
MIN