ST7MDTU3-EPB/US STMicroelectronics, ST7MDTU3-EPB/US Datasheet
ST7MDTU3-EPB/US
Specifications of ST7MDTU3-EPB/US
Available stocks
Related parts for ST7MDTU3-EPB/US
ST7MDTU3-EPB/US Summary of contents
Page 1
... STMicroelectronics Programming board www.st.com ST7-EPB UM0028 User manual Rev 4 June 2006 ...
Page 2
BLANK ...
Page 3
Introduction Thanks for choosing ST7! This manual will help you setup and start using your ST7-EPB programming board. ST7-EPB programming boards allow you to program ST7 microcontrollers that have EPROM, EEPROM and FLASH memories. Your programming board links, via parallel ...
Page 4
Introduction About the user manuals... This manual will help you setup your ST7-EPB programming board and connect it to your PC. Here, you will find: ■ Setup instructions ■ Information about in-circuit programming connections For information about the hardware and ...
Page 5
ST7-EPB Contents 1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 6
Getting Started 1 Getting Started Your ST7-EPB programming board is equipped with the sockets you will need to program a sub-family of ST7 MCUs. In addition, some programming boards also support connections for In-Circuit Programming (ICP Situ ...
Page 7
ST7-EPB Figure 2. Parts delivered with ST7-EPBs (not to scale) 1.2 Setting up your ST7-EPB To setup your ST7-EPB programming board: 1. Shut down and power-off the host PC. 2. Connect one end of the supplied parallel cable to the ...
Page 8
Getting Started Figure 3. Installing MCU in a ZIF socket 4. Lock the device in place by lowering the lever again. Use ST7 Visual Programmer to program your device. For more detailed information about its use, refer to the ...
Page 9
ST7-EPB Note: When using the ST7MDTS1-EPB, the VDD_APPLI is not connected to the ST7. When setting up your application for in-circuit programming, refer to the ICP Interface diagram in the In-CIrcuit Programming section of the ST7SCR Datasheet, instead of the ...
Page 10
... Before programming the OSCx option bits, make sure you have chosen the right options configuration.The OSCx option bits are very important. If you program the wrong OSCx option bits, depending on your hardware configuration, you may not be able to reprogram the device in ISP mode. 10/15 • ST7MDTU2-EPB ST7MDTU5-EPB ST7MDTU3-EPB . DD UM0028 Rev 4 ST7-EPB ...
Page 11
ST7-EPB 2 Hardware Features 2.1 Parallel port connection The ST7 EPB communicates with your host PC (running STVP7) via a parallel port connection. Most communication failures between the host PC running STVP7 and your programming board stem from problems in ...
Page 12
Appendix A Revision history Appendix A Revision history Date November-2000 18-June-2001 21-April-2004 12-November-2004 27-June-2006 12/15 Revision • Transferred to user manual format 2 • Added new programmers • Added information about programming in ICP mode 3 • Removed list of ...
Page 13
ST7-EPB Appendix B Safety Requirements ● Any tester, equipment, or tool used at any production step, or for any manipulation of semiconductor devices, must have its shield connected to ground. ● The product must be placed on a conductive table ...
Page 14
... Product Support If you experience any problems with this product you need spare parts or repairs, contact the distributor or the STMicroelectronics sales office where you purchased the product. Phone numbers for major sales regions are provided in the In addition, at our Internet site www.st.com/mcu, you will find a complete listing of ST sales ...
Page 15
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...