Z8ICE001ZEM Zilog, Z8ICE001ZEM Datasheet - Page 5

• Manufacturer Part Number: Z8ICE001ZEM
• Description: Z8 PLUS EMULATOR/PROGRAMMER
• Manufacturer: Zilog
• Series: Z8 OTPr
• Type: In-Circuit Emulator Systemr

Specifications of Z8ICE001ZEM

• Contents: Emulator Board, Cables, Software and Documentation
• For Use With/related Products: Zilog Z8Plus™ Microcontrollers
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 269-2033

ZiLOG
PRECAUTIONS
All Devices
1. This emulator is only supported by ZDS version 2.12
2. The emulator cannot be operated while performing
3. Ensure that the target cable is correctly aligned (pin 1
4. If the Program Counter jumps to an unknown address:
5. If the Program keeps resetting:
6. Check the
7. Do not start the emulator with an OTP device in the
8. A shorted OTP device can crash the emulator when
DS008801-Z8X1299
or later.
ESD/EMI testing on the target board.
to pin 1) before inserting into the target system.
Incorrect alignment may damage the emulator and/or
the target system.
a. The Stack may have overflowed into the general-
b. An extra
a. The Program Counter rolled over from value
b. The Watch-Dog Timer (
required for emulation. The actual specification may
differ from the ICE chip specifications.
programming socket. The emulator may not start up
correctly and the device may become corrupted.
inserted into the OTP programming socket. If a part is
inserted in such a way as to cause a temporary short,
then functionality is lost. An attempt to perform
BLANK CHECK
appear continuously. The Windows application must
be reset and restarted.
purpose register locations, and/or
encountered.
address
beginning of the program.
from devices with the
T
to value
POR
POP
and
on such a part causes the
T
,
0000
WDT
PUSH
WDT
specifications of the device
and proceeded back to the
WDT
,
IRET
feature.
) was not refreshed
, or
hourglass
RET
was
end
to
9. Do not press the emulator’s
Notes: The
10. When device serialization is enabled in the
11. When interrupts are enabled, breakpointing after a
12. The
13. The emulator does not execute the first instruction to
the ICEBOX is in the OTP dialog for programming. If
MASTER RESET
performing OTP programming, close the
box and reopen it to reload the information back to the
hardware.
dialog, ZDS copies the current serial number to code
memory immediately before performing a
operation. If this software action is undesirable, then
device serialization should be disabled prior to
invoking the
HALT
instruction in the interrupt service routine that is
serviced when an interrupt occurs.
the parts. Particularly, the
differently than the device. Set this register to the
desired value as the first instruction in the program.
load the
then
to execute correctly, the user should press the
RESET+GO
of the ICEBOX, and is not to be confused with the
button on the outside of the unit.
In this instance, he ICEBOX is really idle, although the
Command Status indicates
reestablishes the communication link when Retry is
selected in the Out of Synchronization with the Emulator
dialog box.
RESET
GO
instruction, the emulator breaks at the first
MASTER RESET
TCTLHI
from ZDS or the GUI. For the first instruction
default state of the emulator differs from
button.
VERIFY
register if the user presses
is pressed while the GUI is
operation.
is physically located on the inside
PROCESSING
TCTLHI
MASTER RESET
Z8Plus Emulator
register is reset
Z8ICE001ZEM
after the GUI
OTP
RESET
VERIFY
RESET
dialog
when
OTP
and
5