101-1053 Rabbit Semiconductor, 101-1053 Datasheet - Page 45
101-1053
Manufacturer Part Number
101-1053
Description
KIT DEV RABBITCORE RCM3365 US
Manufacturer
Rabbit Semiconductor
Series
RabbitCore 3000r
Type
MPU Core Moduler
Datasheet
1.20-101-1051.pdf
(164 pages)
Specifications of 101-1053
Contents
RabbitCore Module, Dev. Board, AC Adapter, Cable and Dynamic C® CD-Rom
Processor To Be Evaluated
RCM3365
Interface Type
Ethernet
Maximum Operating Temperature
+ 70 C
Operating Supply Voltage
3.15 V to 3.45 V
For Use With/related Products
RCM3365
Lead Free Status / RoHS Status
Lead free by exemption / RoHS compliant by exemption
Other names
316-1074
- Current page: 45 of 164
- Download datasheet (3Mb)
Figure 10 shows how to insert or remove the
. While you remove or insert
xD-Picture Card
the
, take care to avoid touching the electrical contacts on the bottom of the
xD-Picture Card
card to prevent electrostatic discharge damage to the card and to keep any moisture or
other contaminants off the contacts. Do not remove or insert the
while it is
xD-Picture Card
being accessed.
Figure 10. Insertion/Removal of xD-Picture Card
It is possible to hot-swap xD-Picture Cards without removing power from the RCM3365/
RCM3375 module. The file system must be closed before the cards can be hot-swapped.
The chip selects associated with the NAND flash and the xD-Picture Card must be set to
their inactive state, and read/write operations addressed to the NAND flash area cannot be
allowed to occur. These operations can be initiated in software by sensing an external
switch actuated by the user, and the xD-Picture Card can then be removed and replaced
with a different one. Once the application program detects a new card, the file system can
be opened. These steps allow the xD-Picture Card to be installed or removed without
affecting either the program, which continues to run on the RCM3365/RCM3375 module,
or the data stored on the xD-Picture Card.
The FAT_HOT_SWAP_336x0.C sample program in the SAMPLES\FileSystem\
folder illustrates this hot-swapping procedure.
Rabbit recommends that you use header J6 only for the
since other
xD-Picture Card
devices are not supported. Be careful to remove and insert the
as shown,
xD-Picture Card
and be careful not to insert any foreign objects, which may short out the contacts and lead
to the destruction of your
.
xD-Picture Card
Sample programs in the SAMPLES\RCM3360\NANDFlash folder illustrate the use of
the NAND flash. These sample programs are described in Section 3.2.1, “Use of NAND
Flash.” Pay careful attention to the sample programs to see how to close files and secure
any data on the
before you remove it.
xD-Picture Card
User’s Manual
39
Related parts for 101-1053
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEV STANDARD RCM5700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
BL4S200 TOOL KIT
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV FOR BL2500 COYOTE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories Keypad/Display Unit 5V Panel Mount
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
Single Board Computers 24VDC/110 Power Supp
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor