AD9786-EB Analog Devices Inc, AD9786-EB Datasheet - Page 12

• Manufacturer Part Number: AD9786-EB
• Description: BOARD EVALUATION FOR AD9786
• Manufacturer: Analog Devices Inc
• Series: TxDAC+®r

Specifications of AD9786-EB

• Number Of Dac's: 1
• Number Of Bits: 16
• Outputs And Type: 1, Differential
• Sampling Rate (per Second): 500M
• Data Interface: Parallel
• Dac Type: Current
• Voltage Supply Source: Single
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD9786
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD9786
TERMINOLOGY
Linearity Error (Integral Nonlinearity or INL)
Linearity error is defined as the maximum deviation of the
actual analog output from the ideal output, determined by a
straight line drawn from zero to full scale.
Differential Nonlinearity (DNL)
DNL is the measure of the variation in analog value, normal-
ized to full scale, associated with a 1 LSB change in digital
input code.
Monotonicity
A D/A converter is monotonic if the output either increases or
remains constant as the digital input increases.
Offset Error
The deviation of the output current from the ideal of zero is
called offset error. For I
inputs are all 0s. For I
inputs are set to 1.
Gain Error
The difference between the actual and ideal output span. The
actual span is determined by the output when all inputs are set
to 1, minus the output when all inputs are set to 0.
Output Compliance Range
The range of allowable voltage at the output of a current-output
DAC. Operation beyond the maximum compliance limits can
cause either output stage saturation or breakdown, resulting in
nonlinear performance.
Temperature Drift
Temperature drift is specified as the maximum change from the
ambient (+25°C) value to the value at either T
offset and gain drift, the drift is reported in ppm of full-scale
range (FSR) per degree Celsius. For reference drift, the drift is
reported in ppm per degree Celsius.
Power Supply Rejection
The maximum change in the full-scale output as the supplies
are varied from minimum to maximum specified voltages.
OUTB
OUTA
, 0 mA output is expected when all
, 0 mA output is expected when the
MIN
or T
MAX
. For
Rev. B | Page 12 of 56
Settling Time
The time required for the output to reach and remain within a
specified error band about its final value, measured from the
start of the output transition.
Glitch Impulse
Asymmetrical switching times in a DAC give rise to undesired
output transients that are quantified by a glitch impulse. It is
specified as the net area of the glitch in pV-sec.
Spurious-Free Dynamic Range (SFDR)
The difference between the rms amplitude of the output signal
and the amplitude of the peak spurious signal over the specified
bandwidth. The units are often in dBc (dB with respect to the
carrier).
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first six harmonic
components to the rms value of the measured fundamental. It is
expressed as a percentage or in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency, excluding the first six harmonics and dc.
The value for SNR is expressed in decibels.
Interpolation Filter
If the digital inputs to the DAC are sampled at a multiple rate of
f
a sharp transition band near f
appear around f
Pass Band
Frequency band in which any input applied therein passes
unattenuated to the DAC output.
Stop-Band Rejection
The amount of attenuation of a frequency outside the pass band
applied to the DAC, relative to a full-scale signal applied at the
DAC input within the pass band.
DATA
(interpolation rate), a digital filter can be constructed that has
DAC
(output data rate) can be greatly suppressed.
DATA
/2. Images that would typically