KS8695P-MDP-EVAL Micrel Inc, KS8695P-MDP-EVAL Datasheet - Page 30

• Manufacturer Part Number: KS8695P-MDP-EVAL
• Description: EVAL KIT EXPERIMENTAL KS8695PMPD
• Manufacturer: Micrel Inc

Specifications of KS8695P-MDP-EVAL

• Lead Free Status / RoHS Status: Not applicable / Not applicable

General Purpose I/O Pins (continued)
Advanced Memory Interface (SDRAM/ROM/FLASH/SRAM/EXTERNAL I/O)
Note:
1. I = Input.
Micrel, Inc.
May 2006
B10
Pin
Pin
M3
M2
M1
D1
C1
B1
A2
D2
D3
U7
P4
P3
N4
N3
N2
N1
P2
P1
R3
R2
R1
U1
U2
U3
U4
T7
T2
T1
T3
T4
O = Output.
I/O = Bidirectional.
ADDR21/BA1
ADDR20/BA0
PCLKOUT3
PCLKOUT2
PCLKOUT1
PCLKOUT0
MPCIACTN
CLKRUNN
ADDR[19]
ADDR[18]
ADDR[17]
ADDR[16]
ADDR[15]
ADDR[14]
ADDR[13]
ADDR[12]
ADDR[11]
ADDR[10]
SDOCLK
ADDR[9]
ADDR[8]
ADDR[7]
ADDR[6]
ADDR[5]
ADDR[4]
ADDR[3]
ADDR[2]
ADDR[1]
ADDR[0]
SDICLK
PBMS
Name
Name
I/O Type
I/O Type
I/O
O
O
O
O
O
O
O
O
O
I
I
(1)
(1)
Description
PCI clock output 3. In host bridge mode driven as 33MHz
In guest bridge mode, this signal is reserved
PCI clock output 2. In host bridge mode driven as 33MHz
In guest bridge mode, this signal is reserved
PCI clock output 1. In host bridge mode driven as 33MHz
In guest bridge mode, this signal is reserved
PCI clock output 0. In host bridge mode driven as 33MHz
In guest bridge mode, this signal is reserved
This is a cardbus only signal. The CLKRUNN signal is used by portable cardbus
devices to request that the system turn on the bus clock. Output is always active in
cardbus and miniPCI modes.
MiniPCI active. This signal is asserted by the PCI device to indicate that its current
function requires full system performance. MPCIACTN is an open drain output
signal. In miniPCI mode, this signal is always low.
PCI bridge mode select. This selects the operating mode for the PCI bridge. When
PBMS is high, the host bridge mode is selected and the on-chip PCI bus arbiter is
enabled. When PBMS is low, the guest bridge mode is selected and the on-chip
arbiter is disabled.
Description
SDRAM Clock In: SDRAM clock input for the SDRAM memory controller interface.
System/SDRAM Clock Out: Output of the internal system clock, it is also used as
the clock signal for SDRAM interface.
Address Bit 21/Bank Address Input 1: Address bit 21 for asynchronous accesses.
Bank Address Input bit 1 for SDRAM accesses.
Address Bit 20/Bank Address Input 0: Address bit 20 for asynchronous accesses.
Bank Address Input bit 0 for SDRAM accesses.
Address Bus: The 22-bit address bus (including ADDR[21:20] above) covers 4M
word memory space shared by ROM/SRAM/FLASH, SDRAM, and external I/O
banks. During the SDRAM cycles, the internal address bus is used to generate RAS
and CAS addresses for the SDRAM. The number of column address bits in the
SDRAM banks can be programmed from 8 to 11 bits via the SDRAM control
registers. ADDR[12:0] are the SDRAM address and ADDR[21:20] are the SDRAM
bank address. During other cycles, the ADDR[21:0] is the byte address of the data
transfer. For SDRAM and FLASH/ROM/SRAM, connect all address lines, i.e. A0 to
A0, A1 to A1, etc. The memory controller automatically handles address line
adjustments for the 8/16/32 bit accesses. For external I/O devices, the user needs
to connect address lines for 8/16/32 bit accesses.
30
M9999-051806
KS8695P