G6JU-2P-Y DC12 Omron, G6JU-2P-Y DC12 Datasheet
G6JU-2P-Y DC12
Specifications of G6JU-2P-Y DC12
G6JU2PYDC12
Z2145
Related parts for G6JU-2P-Y DC12
G6JU-2P-Y DC12 Summary of contents
Page 1
... Application Examples Communications equipment, measurement devices, computer peripheral devices, office automation equipment, and audio-visual products. Model Non-latching Single coil latching G6J-2P-Y G6JU-2P-Y G6J-2FL-Y G6JU-2FL-Y G6J-2FS-Y G6JU-2FS-Y 4. Packaging None: Tube packaging TR: Tape and reel packaging 9. Rated Coil Voltage 3, 4.5, 5, 12, 24 Surface-mounting Relay G6J-Y 57 ...
Page 2
... Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%. 2. The operating characteristics are measured at a coil temperature of 23°C. 3. The maximum voltage is the highest voltage that can be imposed on the Relay coil instantaneously. G6JU-Y Single coil, Latching (G6JU-2P-Y, G6JU-2FL-Y, G6JU-2FS-Y) Rated voltage Rated current ...
Page 3
... The insulation resistance was measured with a 500-VDC Megger Tester applied to the same parts as those for checking the dielectric strength. 4. The above values are initial values. Standard non-latching relays G6J-2P-Y, G6J-2FS-Y, G6J-2FL max. (approx. 0.9 ms min. (at 100% rated coil voltage) 2 (approx. 100G) 2 (approx. 75G) Surface-mounting Relay Single coil latching relays G6JU-2P-Y, G6JU-2FS-Y, G6JU-2FL-Y G6J-Y 59 ...
Page 4
... Unit: m Sample: G6J-2P-Y Z' Number of Relays Conditions: Shock is applied in ±X, ±Y, and ±Z directions three times each with and without energizing the Relays to check the number of contact malfunctions. Contact Reliability Test (See note.) 1,000 Sample: G6J-2P-Y NO contact Number of Relays: 10 Test conditions: 10 μA resistive load ...
Page 5
... Frequency (MHz) Surface-mounting Relay Average value + +20 +10 0 −10 −20 Sample: G6J-2P-Y Must Operate voltage Number of Relays: 5 Must Release voltage −30 −1,200 −800 −400 0 400 800 1,200 External magnetic field (A/m) Average value 0 3.5 3 2.5 2-pole return loss 2 1-pole return loss 1 ...
Page 6
... Must Operate bounce time Must Operate bounce time 35 Must Release bounce time 35 Must Release bounce time Sample: G6J-2P-Y Sample: G6J-2P-Y Number of Relays: 30 Number of Relays 0.5 1 1 0.5 1 1.5 2 2.5 3 Time (ms) Time (ms) G6J-Y Vibration Resistance 5.0 4.0 3.0 2.0 1.0 Must Operate voltage 0 ...
Page 7
... Orientation mark holes 3.2 − (1.25) G6JU-2P-Y Orientation mark − − Terminal Arrangement/ Internal Connections (Top View) G6J-2FS-Y Orientation mark 2. − 4. G6JU-2FS-Y Orientation mark − − Terminal Arrangement/ Internal Connections (Top View) G6J-2FL-Y Orientation mark 3 − 5 G6JU-2FL-Y Orientation mark − − ...
Page 8
... Surface-mounting Relay Carrier Tape Dimensions G6J-2FS-Y, G6JU-2FS-Y 16± 0.1 2± 4± 0.1 0.1 Stopper (green) A 6.2± 8.3± 0.1 5° max. G6J-2FL-Y, G6JU-2FL-Y 16± 0.1 2± 4± 0.1 A 7.9± 0.1 5° max. Orientation mark Pulling direction dia. 13± 0.2 ± ...
Page 9
... Contact form Coil rating DPDT G6J-2P-Y, 2FS-Y, 2FL- VDC G6JU-2P-Y, 2FS-Y, 2FL- VDC • The thickness of cream solder to be applied should be between 150 and 200 μm on OMRON's recommended PCB pattern. • In order to perform correct soldering recommended that the correct soldering conditions be maintained as shown below on the left-hand side ...
Page 10
... Mounting Latching Relays The Latching Relays are reset before shipping. If excessive vibration or shock is imposed, however, the Latching Relays may be set acci- dentally. Be sure to apply a reset signal before use. Make sure that the vibration or shock that is generated by other devices on the same panel does not exceed the rated value of the Latching Relays ...
Page 11
... Seller within 30 days of receipt of shipment. III. PRECAUTIONS 1. Suitability THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE BUYER’ ...
Page 12
... THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section. ...