ASSR-3210-003E Avago Technologies US Inc., ASSR-3210-003E Datasheet - Page 10

• Manufacturer Part Number: ASSR-3210-003E
• Description: RELAY SSR SPST SGL 0.2A 4-SOP
• Manufacturer: Avago Technologies US Inc.
• Series: ASSRr

Specifications of ASSR-3210-003E

• Package / Case: 4-SOP
• Circuit: SPST-NO (1 Form A)
• Output Type: AC, DC
• On-state Resistance: 10 Ohm
• Load Current: 200mA
• Voltage - Input: 1.3VDC
• Voltage - Load: 0 ~ 250 V
• Mounting Type: Surface Mount
• Termination Style: Gull Wing
• Load Voltage Rating: 250 V
• Load Current Rating: 0.2 A
• Contact Form: 1 Form A
• Output Device: MOSFET
• Relay Type: Solid State
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Switching Specifications (AC)
Over recommended operating T
Notes:
1. For derating, refer to Figure 1 and 2.
2. The voltage across the output terminals of the relay should not exceed this rated withstand voltage. Over-voltage protection circuits should be
3. Threshold to switch device is I
4. Device is considered as a two terminal device:
5. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
6. During the pulsed R
Applications Information
On-Resistance and Derating Curves
The Output On-Resistance, R
sheet, is the resistance measured across the output
contact when a pulsed current signal (Io=0.2A) is ap-
plied to the output pins. The use of a pulsed signal (≤
30ms) implies that each junction temperature is equal
to the ambient and case temperatures. The steady-state
resistance, Rss, on the other hand, is the value of the re-
sistance measured across the output contact when a DC
current signal is applied to the output pins for a duration
sufficient to reach thermal equilibrium. Rss includes the
effects of the temperature rise in the device.
Derating curves are shown in Figures 1 and 2, specifying
the maximum output current allowable for a given am-
10
Parameter
Turn On Time
Turn Off Time
Output Transient Rejection
Input-Output
Transient Rejection
added in some applications to protect against over-voltage transients. ”
I
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your
equipment level safety specification, or Avago Technologies Application Note 1074, “Optocoupler Input-Output Endurance Voltage. ”
F
=5mA. Refer to application information in next section of this datasheet.
ASSR-3210 - pin 1, 2 shorted and pin 3, 4 shorted.
ASSR-3211 - pin 1, 2, 3 shorted and pin 4, 5, 6 shorted.
ASSR-3220 - pin 1, 2, 3, 4 shorted and pin 5, 6, 7, 8 shorted.
(ON)
measurement ( I
Sym.
T
T
dV
dV
ON
OFF
O
I-O
F
/dt
≥ 0.5mA, however, for qualified device performance over temperature range, it is recommended to operate at
/dt
(ON)
A
, specified in this data
= -40°C to 85°C, I
O
Min.
1
1
duration ≤30ms), ambient (T
Typ.
0.25
0.02
7
≥10
F
= 5mA to 10mA, unless otherwise specified.
Max.
1.0
2.0
0.2
0.5
A
bient temperature. The maximum allowable output cur-
rent and power dissipation are related by the expression
Rss=Po(max)/(Io(max))
Staying within the safe area assures that the steady state
MOSFET junction temperature remains less than 125°C.
Turn On Time and Turn Off Time Variation
The ASSR-32XX Series exhibits a very fast turn on and
turn off time. Both the turn on and turn off time can be
adjusted by choosing proper forward current as depicted
in Figures  and 11. The changes of the turn on and turn
off time with ambient temperature are also shown in
Figures 10 and 12.
) and case temperature (T
Units
ms
ms
ms
ms
kV/µs
kV/µs
Conditions
I
T
I
I
T
I
DV
DV
F
F
F
F
A
A
=5mA, I
=5mA, I
=5mA, I
=5mA, I
=25°C
=25°C
O
I-O
=250V, T
C
=1000V, T
2
) are equal.
from which Rss can be calculated.
O
O
O
O
=200mA,
=200mA
=200mA,
=200mA
A
=25°C
A
=25°C
Fig.
9, 13
10
11, 13
12
14
15
Note