LT4H-DC24VS Panasonic Electric Works, LT4H-DC24VS Datasheet - Page 4

• Manufacturer Part Number: LT4H-DC24VS
• Description: TIMER RELAY DIG 24VDC SCREW TERM
• Manufacturer: Panasonic Electric Works
• Series: LT4Hr

Specifications of LT4H-DC24VS

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 255-1217

LT4H/-L
Specifications
Applicable standard
36
Item
Rating
Time
accuracy
(max.)
Contact
Life
Electrical
Mechanical
Operating
conditions
Connection
Protective construction
EMC
Safety standard
Rated operating voltage
Rated frequency
Rated power consumption
Rated control capacity
Time range
Time counting direction
Operation mode
Start/Reset/Stop input
Lock input
Input signal
Indication
Power failure memory
method
Operating time fluctuation
Temperature error
Voltage error
Setting error
Contact arrangement
Contact resistance (Initial value)
Contact material
Mechanical (contact)
Electrical (contact)
Allowable operating voltage range
Breakdown voltage
(Initial value)
Insulation resistance
(Initial value)
Operating voltage reset
time
Temperature rise
Vibration
resistance
Shock
resistance
Ambient temperature
Ambient humidity
Air pressure
Ripple rate
(EMI)EN61000-6-4
Radiation interference electric field strength
Noise terminal voltage
(EMS)EN61000-6-2
Static discharge immunity
RF electromagnetic field immunity
EFT/B immunity
Surge immunity
Conductivity noise immunity
Power frequency magnetic field immunity
Voltage dip/Instantaneous stop/Voltage fluctuation immunity
Functional
Destructive
Functional
Destructive
Type
(under the flow of nominal operating current at nominal voltage)
2,000 Vrms for 1 min: Between live and dead metal parts (11-pin)
2,000 Vrms for 1 min: Between input and output
1,000 Vrms for 1 min: Between contacts
Min. 100 MΩ: Between input and output
100 to 240 V AC, 24 V AC,
Min. input signal width: 1 ms, 20 ms (2 directions by selected by DIP switch) (The 8-pin type does not have a stop input.)
AC type AC/DC type
Min. 2 × 10
EN61812-1
50/60 Hz common
7-segment LCD (LT4H, LT4H-L common), Elapsed value (backlight red LED), Setting value (backlight yellow LED)
A (Power ON delay 1), A2 (Power ON delay 2), B (Signal ON delay), C (Signal OFF delay), D (Pulse one-shot),
24 V AC/DC
Max. 10 V A
9.999 s, 99.99 s, 999.9 s, 9999 s, 99 min 59 s, 999.9 min, 99 h 59 min, 999.9 h (selected by DIP switch)
1.0 × 10
± (0.005 % + 20 ms) in case of input signal start
—
Between live and dead metal parts
Between contacts
± (0.005 % + 50 ms) in case of power on start
5 A, 250 V AC (resistive load)
7
ope. (Except for switch operation parts)
E (Pulse ON delay), F (Signal Flicker), G (Totalizing ON delay) (selectable by DIP switch)
100 mΩ (at 1 A 6 V DC)
5
Timed-out 1 Form C
ope. (At rated control voltage)
10 to 55 Hz: 1 cycle/min single amplitude of 0.35 mm
Ralay output type
Ag alloy/Au flash
10 to 55 Hz: 1 cycle/min single amplitude of 0.75 mm
Open collector input Input impedance: Max. 1
Max. 65° C
Min. input signal width: 20 ms (The 8-pin type does not have a lock input.)
Open impedance: 100kΩ or less, Max. energized voltage: 40V DC
12 to 24 V DC
Min. 294 m
20 % or less
Min. 98 m
Max. 3 W
DC type
(2 directions selectable by DIP switch)
85 to 110 % of rated operating voltage
IP66 (front panel with rubber gasket)
Addition (UP)/Subtraction (DOWN)
EN55011 Group1 ClassA
EN55011 Group1 ClassA
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11 10 ms, 30% (rated voltage)
—
–10° C to 55° C
Max. 85 % RH (non-condensing)
EEP-ROM (Min. 10
(At 500V DC)
8-pin/11-pin/screw terminal
321.522
964.567
860 to 1,060 h Pa
Max. 0.5 s
ft./s
ft./s
4 kV contact
8 kV air
10 V/m AM modulation (80 MHz to 1 GHz)
10 V/m pulse modulation (895 MHz to 905 MHz)
2 kV (power supply line)
1 kV (signal line)
1 kV (power line)
10 V/m AM modulation (0.15 MHz to 80 MHz)
30 A/m (50 Hz)
100 ms, 60% (rated voltage)
1,000 ms, 60% (rated voltage)
5,000 ms, 95% (rated voltage)
+14° F to +131° F
2,000 Vrms for 1 min: Between live and dead metal parts (Pin type)
2,000 Vrms for 1 min: Between input and output
Min. 100 MΩ: Between live and dead metal parts
2
Pollution Degree 2/Overvoltage Category II
2
100 to 240 V AC, 24 V AC,
(4 times on 3 axes)
(5 times on 3 axes)
5
overwriting)
AC type AC/DC type
50/60 Hz common
kΩ; Residual voltage: Max. 2 V
24 V AC/DC
Max. 10 V A
[
.014 inch
Min. 10
Timed-out 1 Form A (Open collector)
Operating voltage: 85 to 110%
Temperature: –10 to +55°C
Min. input signal width: 1ms
.030 inch
—
Between input and output
7
Transistor output type
ope. (At rated control voltage)
(10 min on 3 axes)
100 mA, 30 V DC
(1 h on 3 axes)
—
—
—
—
12 to 24 V DC
+14 to +131°F
20 % or less
Max. 3 W
DC type
—
(At 500V DC)
]