PDH10-37 Panduit Corp, PDH10-37 Datasheet - Page 32

• Manufacturer Part Number: PDH10-37
• Description: HOSE AIR SUPPLY
• Manufacturer: Panduit Corp
• Type: Accessory, Hoser

Specifications of PDH10-37

• Features: -
• For Use With/related Products: -

No exit sensor
seen - service
tool soon
Switch #X is
stuck or broken
Restore past
tool count?
Jaw sensor
error
System error #X
Cable tie too
loose on
bundle.
Cable tie too
tight on bundle.
Cable tie not cut
off flush to
head.
Cable tie does
not stay on
bundle.
Misfeed; cable
tie cycle was
not completed
FUNCTIONAL MESSAGE TROUBLESHOOTING
CABLE TIE INSTALLATION TROUBLESHOOTING
SYMPTOM
MESSAGE
PAT1M/PAT1.5M: PA22222A01_03
A. Tool tension setting is too low.
B. Operator holding tool at angle to
C. Bundle exceeds .82" (21 mm) /
D. Tool is held away from bundle by
E. Tool is pulled on as the tie is being
Tool tension setting is too high.
A. Tool tension setting too high for
B. Operator holding tool at angle to
C. Tool is pulled on as the tie is being
D. Tool is held away from bundle by
A. Bundle exceeds .82" (21 mm) /
B. Cable ties are too dry and brittle.
C. Tool tension setting is too high.
D. Incoming air pressure is too high.
A. Cable tie path was blocked; bundle
B. Air pressure is not set correctly.
Cable tie in feeder hose when tool was
actuated or dispenser exit sensor is
not functioning properly.
A switch (button #1, 2, 3, 4, or the
trigger) was held down or was stuck
when the dispenser was turned "on".
This message will remain if one of
these five switches has malfunctioned.
Tool counter is not functioning
correctly.
Cable tie stopped in tool gears.
See Page 23.
bundle.
1.31" (33 mm) in diameter.
previously installed tie, harness
support, or other object on bundle.
tensioned.
humidity conditions.
bundle.
tensioned.
previously installed tie, harness
support or other object on bundle.
against jaw tie track.
1.31" (33 mm) in diameter.
POSSIBLE CAUSE
POSSIBLE CAUSE
PAT1M / PAT1.5M OPERATION MANUAL
A. Increase tool tension setting.
B. Hold tool perpendicular to bundle in both directions.
C. Dress the wires to result in a more compact bundle for the
D. Do not install cable ties too close to other cable ties, harness
E. Allow tool to seek its own position as the tie is being tensioned.
Decrease tool tension setting.
A. Decrease tool tension setting.
B. Hold tool perpendicular to bundle in both directions.
C. Allow tool to seek its own position as the tie is being tensioned.
D. Do not install cable ties too close to other cable ties, harness
A. Dress the wires to result in a more compact bundle for the
B. Store cable ties properly and use before expiration date.
C. Decrease tool tension setting.
D. Set air pressure between 65 and 85 PSIG (4,5 and 5,8 bar),
A. DO NOT place bundle forcefully against jaw tie track.
B. Verify that air pressure is at 65 PSIG (4,5 bar) (minimum). Air
1. Resume operation.
2. If the same error is repeated, the exit sensor lens may be dirty,
3. Clean the exit sensor lens (Refer to the Cleaning the
4. If the same error is repeated, notify your maintenance
1. The message will disappear when the switch (button #1, 2, 3,
2. If the message does not disappear, then the specific switch
1. Press the "Yes" button and resume operation.
2. If the same error is repeated, notify your maintenance
1. Press "Buzzer" button to turn buzzer "off".
2. Remove the cable tie from the jaw area.
3. Press the "Continue" button and resume operation.
See Page 23.
Page: 30 of 36
supports or other objects on bundle.
specific tool being used.
with a maximum 10 PSI (0,7 bar) drop.
pressure can be increased by 5 PSI (0,35 bar) increments until
cable ties feed properly. Do not exceed 85 PSIG (5,8 bar)
(maximum).
or it may not be functioning properly.
Dispenser Exit Sensor Lens section on Page 26).
department.
4, or the trigger) has been freed or released.
(button #1, 2, 3, 4, or the trigger) is bad. Contact your
maintenance department to have the switch replaced.
department.
specific tool being used.
supports or other objects on bundle.
CORRECTIVE ACTION
CORRECTIVE ACTION
Dec., 2007