GA342D1XGF150JY02L Murata Electronics North America, GA342D1XGF150JY02L Datasheet - Page 55

• Manufacturer Part Number: GA342D1XGF150JY02L
• Description: CAP CER 250VAC 15PF 5% SL 1808
• Manufacturer: Murata Electronics North America
• Series: GFr

Specifications of GA342D1XGF150JY02L

• Capacitance: 15pF
• Voltage - Rated: 250VAC
• Tolerance: ±5%
• Temperature Coefficient: SL
• Mounting Type: Surface Mount, MLCC
• Operating Temperature: 20°C ~ 85°C
• Features: High Voltage
• Applications: Safety
• Ratings: X1Y2
• Package / Case: 1808 (4520 Metric)
• Size / Dimension: 0.177" L x 0.079" W (4.50mm x 2.00mm)
• Thickness: 2.00mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Other names: 490-3461-2

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
11
12 Deflection
13
GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection
Continued from the preceding page.
Vibration
Resistance
Solderability of
Termination
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection
Item
Appearance
Capacitance
Q/D.F.
Appearance
Capacitance
Change
No defects or abnormalities
Within the specified tolerance
30pF and over: QU1000
30pF and below:
C: Nominal Capacitance (pF)
No marking defects
Within 5% or 0.5pF
(whichever is larger)
75% of the terminations are to be soldered evenly and
continuously.
Compensating Type
Temperature
QU400+20C
R230
When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
Specifications
Capacitance meter
45
When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
Fig. 3a
20
[B1, B3, R6, R7, C8]
W.V.: 100V
W.V.: 50/35/25V:
*GRM32D R7/R6/C8 1E106: 0.035 max.
W.V.: 16/10V: 0.035 max.
W.V.: 6.3/4V
[E4]
W.V.: 25Vmin: 0.025 max.
[F1, F5]
W.V.: 25V min.
W.V.: 16/10V: 0.125 max.
W.V.: 6.3V: 0.15 max.
Within 10%
50
Please refer to individual specifications (our product specifications or the approval sheet).
Pressurize
45
Pressurizing
speed: 1.0mm/sec.
High Dielectric Type
: 0.025 max. (CF0.068 F)
: 0.05 max. (CU0.068 F)
: 0.025 max.*
: 0.05 max. (CF3.3 F)
: 0.1 max. (CU3.3 F)
: 0.05 max. (CF0.1 F)
: 0.09 max. (CU0.1 F)
Flexure : V1
(Note 1) These Specifications and Test Methods indicate typical inspection.
Solder the capacitor on the test jig (glass epoxy board) in the
same manner and under the same conditions as (10).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually
perpendicular directions (total of 6 hours).
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2a using a eutectic solder. Then apply a force in the
direction shown in Fig. 3a for 5 1 sec. The soldering should be
done by the reflow method and should be conducted with care
so that the soldering is uniform and free of defects such as heat
shock.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion).
Preheat at 80 to 120 C for 10 to 30 seconds.
After preheating, immerse in a eutectic solder solution for
2 0.5 seconds at 230 5 C or Sn-3.0Ag-0.5Cu solder solution
for 2 0.5 seconds at 245 5 C.
GRM02
GRM03
GRM15
GRM18
GRM21
GRM31
GRM32
GRM43
GRM55
Type
0.2
0.3
0.4
1.0
1.2
2.2
2.2
3.5
4.5
Test Method
a
Fig. 2a
100
b
c
a
Continued on the following page.
t: 1.6mm (GRM02/03/15: t: 0.8mm)
0.56
0.9
1.5
3.0
4.0
5.0
5.0
7.0
8.0
b
4.5
0.23
1.65
0.3
0.5
1.2
2.0
2.9
3.7
5.6
c
(in mm)
53
C02E.pdf
10.12.20