RDER72J104K8K1C11B Murata Electronics North America, RDER72J104K8K1C11B Datasheet - Page 18

• Manufacturer Part Number: RDER72J104K8K1C11B
• Description: CAP CER 100000PF 630V X7R RADIAL
• Manufacturer: Murata Electronics North America
• Series: RDEr

Specifications of RDER72J104K8K1C11B

• Capacitance: 0.1µF
• Voltage - Rated: 630V
• Tolerance: ±10%
• Temperature Coefficient: X7R
• Mounting Type: Through Hole
• Operating Temperature: -55°C ~ 125°C
• Features: High Voltage
• Applications: General Purpose
• Package / Case: Radial
• Size / Dimension: 0.217" L x 0.295" W (5.50mm x 7.50mm)
• Thickness: 4.00mm Max
• Lead Spacing: 0.197" (5.00mm)
• Lead Style: Flat Bent
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ratings: -
• Other names: 490-4821

2
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
16
No.
11 Solderability of Leads
12
13
14
15
16
17
RPE Series Small Size, Large Capacitance Specifications and Test Methods
Specifications and Test Methods
Continued from the preceding page.
Resistance
to
Soldering
Heat
Temperature
Cycle
Humidity
(Steady
State)
Humidity
Load
High
Temperature
Load
Solvent
Resistance
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance No defects or abnormalities
Capacitance
Change
Dielectric
Strength
(Between
Terminals)
Appearance No defects or abnormalities
Capacitance
Change
D.F.
Insulation
Resistance
Dielectric
Strength
(Between
Terminals)
Appearance No defects or abnormalities
Capacitance
Change
D.F.
Insulation
Resistance
Appearance No defects or abnormalities
Capacitance
Change
D.F.
Insulation
Resistance
Appearance No defects or abnormalities
Capacitance
Change
D.F.
Insulation
Resistance
Appearance No defects or abnormalities
Marking
Lead wire should be soldered with uniform coating on the axial
direction over 3/4 of the circumferential direction.
Within T7.5%
No defects
Within T12.5%
0.05 max.
50M · F min.
No defects or abnormalities
Within T12.5%
0.05 max.
50M · F min.
Within T12.5%
0.05 max.
50M · F min.
Within T12.5%
0.04 max.
50M · F min.
Legible
Specifications
The terminal of a capacitor is dipped into a solution of
ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin
in weight proportion) and then into molten solder (JIS-
Z-3282) for 2T0.5 sec. In both cases the depth of
dipping is up to about 1.5 to 2mm from the terminal
body.
Temp. of solder: 245T5˚C Lead Free Solder (Sn-3.0Ag-0.5Cu)
The lead wire is immersed in the melted solder 1.5 to
2mm from the main body at 350T10˚C for 3.5T0.5 sec.
The specified items are measured after 48T4 hrs.
• Pretreatment
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 48T4 hrs.
The capacitor should be subjected to 200 temperature
cycles.
Set the capacitor at 40T2˚C and relative humidity of 90
to 95% for 500
at room temperature, then measure.
Apply the rated voltage at 40T2˚C and relative humidity
of 90 to 95% for 500
48T4 hrs. at room temperature, then measure.
(Charge/Discharge current V 50mA)
Apply a DC voltage of 150% of the rated voltage for
1000
Remove and set for 48T4 hrs. at room temperature,
then measure.
(Charge/Discharge current V 50mA)
• Pretreatment
Apply test voltage for 1 hr., at test temperature. Remove
and set for 48T4 hrs. at room temperature.
The capacitor should be fully immersed, unagitated, in
reagent at 20 to 25 ˚C for 30T5 sec. and then remove
gently. Marking on the surface of the capacitor should
immediately be visually examined.
Reagent :
• Isopropyl alcohol
Step
1
2
3
4
W
Y
48
0
hrs. at the maximum operating temperature.
235T5˚C H60A or H63A Eutectic Solder
W
Y
Temperature (˚C)
24
Room Temp.
Room Temp.
0
hrs. Remove and set for 48T4 hrs.
Test Method
125T3
W
Y
-55T3
24
0
hrs. Remove and set for
Time (min)
3 max.
3 max.
30T3
30T3
C49E.pdf
10.3.8