PIC12C671-04I/SM Microchip Technology, PIC12C671-04I/SM Datasheet - Page 260

• Manufacturer Part Number: PIC12C671-04I/SM
• Description: IC MCU OTP 1KX14 A/D 8-SOIJ
• Manufacturer: Microchip Technology
• Series: PIC® 12Cr

Specifications of PIC12C671-04I/SM

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Ram Memory Size: 128Byte
• Cpu Speed: 4MHz
• No. Of Timers: 1
• Digital Ic Case Style: SOIC
• Processor Series: PIC12C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8
• Package: 8SOIJ
• Device Core: PIC
• Family Name: PIC12
• Maximum Speed: 4 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164312 - MODULE SKT FOR PM3 16SOICISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING309-1048 - ADAPTER 8-SOIC TO 8-DIP309-1047 - ADAPTER 8-SOIC TO 8-DIPAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PICmicro MID-RANGE MCU FAMILY
16.3.4
DS31016A-page 16-10
SSPIF
Interrupt flag
SCK
(CKP = 0)
SCK
(CKP = 1)
Master Operation
SDO
SDI
The master can initiate the data transfer at any time because it controls the SCK. The master
determines when the slave (Processor 2) wishes to broadcast data by the software protocol.
In master mode the data is transmitted/received as soon as the SSPBUF register is written to. If
the SPI is only going to receive, the SDO output could be disabled (programmed as an input).
The SSPSR register will continue to shift in the signal present on the SDI pin at the programmed
clock rate. As each byte is received, it will be loaded into the SSPBUF register as if a normal
received byte (interrupts and status bits appropriately set). This could be useful in receiver appli-
cations as a “line activity monitor” mode.
The clock polarity is selected by appropriately programming the CKP bit (SSPCON<4>). This
then would give waveforms for SPI communication as shown in
where the MSb is transmitted first. In master mode, the SPI clock rate (bit rate) is user program-
mable to be one of the following:
• F
• F
• F
• Timer2 output/2
This allows a maximum data rate of 5 Mbps (at 20 MHz).
Figure 16-3: SPI Mode Waveform (Master Mode)
OSC
OSC
OSC
bit7
bit7
/4 (or T
/16 (or 4 • T
/64 (or 16 • T
CY
bit6
)
CY
CY
)
)
bit5
bit4
bit3
bit2
bit1
Figure 16-5
1997 Microchip Technology Inc.
bit0
bit0
and
Figure 16-5