PIC18F24J11-I/SO Microchip Technology, PIC18F24J11-I/SO Datasheet - Page 124

• Manufacturer Part Number: PIC18F24J11-I/SO
• Description: IC PIC MCU FLASH 16K 2V 28-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F24J11-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DM183022, DM183033, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MILAC164332 - MODULE SKT FOR 28SOIC 18F45J10
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F46J11 FAMILY
8.6
External interrupts on the INT0, INT1, INT2 and INT3
pins are edge-triggered. If the corresponding INTEDGx
bit in the INTCON2 register is set (= 1), the interrupt is
triggered by a rising edge; if the bit is clear, the trigger
is on the falling edge. When a valid edge appears on
the INTx pin, the corresponding flag bit and INTxIF are
set. This interrupt can be disabled by clearing the
corresponding enable bit, INTxIE. Flag bit, INTxIF,
must be cleared in software in the Interrupt Service
Routine before re-enabling the interrupt.
All external interrupts (INT0, INT1, INT2 and INT3) can
wake-up the processor from the power-managed
modes if bit, INTxIE, was set prior to going into the
power-managed modes. If the Global Interrupt Enable
bit, GIE, is set, the processor will branch to the interrupt
vector following wake-up.
Interrupt priority for INT1, INT2 and INT3 is determined
by the value contained in the Interrupt Priority bits,
INT1IP (INTCON3<6>), INT2IP (INTCON3<7>) and
INT3IP (INTCON2<1>). There is no priority bit
associated with INT0. It is always a high-priority
interrupt source.
8.7
In 8-bit mode (which is the default), an overflow in the
TMR0 register (FFh → 00h) will set flag bit, TMR0IF. In
16-bit mode, an overflow in the TMR0H:TMR0L register
EXAMPLE 8-1:
DS39932C-page 124
MOVWF
MOVFF
MOVFF
;
; USER ISR CODE
;
MOVFF
MOVF
MOVFF
INTx Pin Interrupts
TMR0 Interrupt
W_TEMP
STATUS, STATUS_TEMP
BSR, BSR_TEMP
BSR_TEMP, BSR
W_TEMP, W
STATUS_TEMP, STATUS
SAVING STATUS, WREG AND BSR REGISTERS IN RAM
; W_TEMP is in virtual bank
; STATUS_TEMP located anywhere
; BSR_TMEP located anywhere
; Restore BSR
; Restore WREG
; Restore STATUS
module.
pair (FFFFh → 0000h) will set TMR0IF. The interrupt
can be enabled/disabled by setting/clearing enable bit,
TMR0IE (INTCON<5>). Interrupt priority for Timer0 is
determined by the value contained in the interrupt prior-
ity bit, TMR0IP (INTCON2<2>). See Section 11.0
“Timer0 Module” for further details on the Timer0
8.8
An input change on PORTB<7:4> sets flag bit, RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit, RBIE (INTCON<3>).
Interrupt priority for PORTB interrupt-on-change is
determined by the value contained in the interrupt
priority bit, RBIP (INTCON2<0>).
8.9
During interrupts, the return PC address is saved on
the stack. Additionally, the WREG, STATUS and BSR
registers are saved on the Fast Return Stack. If a fast
return from interrupt is not used (see Section 5.3
“Data Memory Organization”), the user may need to
save the WREG, STATUS and BSR registers on entry
to the Interrupt Service Routine. Depending on the
user’s application, other registers may also need to be
saved. Example 8-1 saves and restores the WREG,
STATUS and BSR registers during an Interrupt Service
Routine.
PORTB Interrupt-on-Change
Context Saving During Interrupts
© 2009 Microchip Technology Inc.