AT89C51RC2-RLTUL Atmel, AT89C51RC2-RLTUL Datasheet - Page 74

• Manufacturer Part Number: AT89C51RC2-RLTUL
• Description: IC 8051 MCU FLASH 32K 44VQFP
• Manufacturer: Atmel
• Series: 89Cr

Specifications of AT89C51RC2-RLTUL

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1280 B
• Interface Type: UART, SPI
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCUAT89STK-11 - KIT STARTER FOR AT89C51RX2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

Registers
Serial Peripheral Control
Register (SPCON)
74
AT89C51RB2/RC2
Figure 31. SPI Interrupt Requests Generation
There are three registers in the Module that provide control, status and data storage functions. These registers
are describes in the following paragraphs.
•
•
•
•
•
•
Table 56 describes this register and explains the use of each bit
Table 56. SPCON Register
SPCON - Serial Peripheral Control Register (0C3H)
Bit Number
SPR2
SPIF
MODF
SSDIS
The Serial Peripheral Control Register does the following:
Selects one of the Master clock rates
Configure the SPI Module as Master or Slave
Selects serial clock polarity and phase
Enables the SPI Module
Frees the SS pin for a general-purpose
7
7
6
5
4
3
2
SPEN
6
Bit Mnemonic
SSDIS
MSTR
SPR2
SPEN
CPOL
CPHA
SPI Transmitter
CPU Interrupt Request
SSDIS
SPI Receiver/error
CPU Interrupt Request
5
Description
Serial Peripheral Rate 2
Bit with SPR1 and SPR0 define the clock rate.
Serial Peripheral Enable
Cleared to disable the SPI interface.
Set to enable the SPI interface.
SS Disable
Cleared to enable SS in both Master and Slave modes.
Set to disable SS in both Master and Slave modes. In Slave mode,
this bit has no effect if CPHA =’0’. When SSDIS is set, no MODF
interrupt request is generated
Serial Peripheral Master
Cleared to configure the SPI as a Slave.
Set to configure the SPI as a Master.
Clock Polarity
Cleared to have the SCK set to ’0’ in idle state.
Set to have the SCK set to ’1’ in idle low.
Clock Phase
Cleared to have the data sampled when the SCK leaves the idle
state (see CPOL).
Set to have the data sampled when the SCK returns to idle state (see
CPOL).
MSTR
4
CPOL
3
CPU Interrupt Request
SPI
.
CPHA
2
SPR1
1
4180E–8051–10/06
SPR0
0