DSPIC30F6012A-30I/PT Microchip Technology, DSPIC30F6012A-30I/PT Datasheet - Page 5

• Manufacturer Part Number: DSPIC30F6012A-30I/PT
• Description: IC DSPIC MCU/DSP 144K 64TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F6012A-30I/PT

• Program Memory Type: FLASH
• Program Memory Size: 144KB (48K x 24)
• Package / Case: 64-TFQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC30F
• Core: dsPIC
• Maximum Clock Frequency: 30 MHz
• Number Of Programmable I/os: 52
• Data Ram Size: 8 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, DM240002, DM330011
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPAC30F008 - MODULE SKT FOR DSPIC30F 64TQFPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: DSPIC30F6012A30IP

4. Module: I
© 2008 Microchip Technology Inc.
When the I
either in single-master or multi-master mode, the
I
address is detected or not. Therefore, an I
receiver overflow condition occurs and this
condition is indicated by the I2COV flag in the
I2CSTAT register.
This overflow condition inhibits the ability to set the
I
valid data byte is received. Therefore, the I
slave Interrupt Service Routine (ISR) is not called
and the I
receiving the next data byte.
Work arounds
To avoid this issue, either of the following two work
arounds can be implemented, depending on the
application requirements.
Work around 1:
For applications in which the I
is not required, the following procedure can be
used to receive valid data bytes:
1. Wait until the RBF flag is set.
2. Poll the I
3. If SI2CF is not set in the corresponding
4. If the SI2CF is set in the corresponding
5. Read the I2CRCV buffer to recover valid data
6. Clear the I
7. Go back to step 1 to continue receiving
2
2
C receiver buffer is filled whether a valid slave
C receive interrupt flag (SI2CF) when the last
Interrupt Flag Status (IFSx) register, a valid
address or data byte has not been received for
the current slave. Execute a dummy read of
the I
the RBF flag. Go back to step 1 until SI2CF is
set and then continue to Step 4.
Interrupt Flag Status (IFSx) register, valid data
has been received. Check the D_A flag to
verify that an address or a data byte has been
received.
bytes. This will also clear the RBF flag.
incoming data bytes.
2
C receiver buffer, I2CRCV; this will clear
2
2
C receiver buffer is not read prior
2
2
C
C module is configured as a slave,
C receiver interrupt SI2CIF flag.
2
C receiver interrupt flag SI2CF.
dsPIC30F6011A/6012A/6013A/6014A
2
C receiver interrupt
2
2
C
C
5. Module: I/O Port – Port Pin Multiplexed
Work around 2:
Use this work around for applications in which the
I
the RBF and the I2COV flags in the I2CSTAT
register are set due to previous data transfers in
the I
slaves); the following procedure can be used to
receive valid data bytes:
1. When a valid slave address byte is detected,
2. Check the status of the D_A flag and the
3. If the D_A flag is cleared and the I2COV flag
4. Clear the I2COV flag and perform a dummy
5. Verify that the recovered address byte
6. If the D_A flag and the I2COV flag are both set,
If the user application enables the auto-baud
feature in the UART module, the I/O pin
multiplexed with the IC1 (Input Capture) pin cannot
be used as a digital input.
Work around
None.
2
C receiver interrupt is required. Assuming that
SI2CF bit is set and the I
service routine is called; however, the RBF and
I2COV bits are already set due to data
transfers between other I
I2COV flag in the I2CSTAT register when
executing the I
are set, an invalid data byte was received but a
valid address byte was received. The overflow
condition occurred because the I
buffer was overflowing with previous I
transfers between other I
condition only occurs after a valid slave
address was detected.
read of the I
clear the RBF bit and recover the valid address
byte. This action will also avoid the loss of the
next data byte due to an overflow condition.
matches the current slave address byte. If they
match, the next data to be received is a valid
data byte.
a valid data byte was received and a previous
valid data byte was lost. It will be necessary to
code for handling this overflow condition.
2
C bus (i.e., between master and other
with IC1
2
2
C receiver buffer, I2CRCV, to
C slave service routine.
2
C nodes.
2
C slave interrupt
2
DS80303E-page 5
C nodes. This
2
C receive
2
C data