C8051F314-GQ Silicon Laboratories Inc, C8051F314-GQ Datasheet - Page 158

• Manufacturer Part Number: C8051F314-GQ
• Description: IC 8051 MCU 8K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F31xr

Specifications of C8051F314-GQ

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 29
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 29
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F310DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 17-chx10-bit
• No. Of I/o's: 29
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1445 - ADAPTER PROGRAM TOOLSTICK F310
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1257

C8051F310/1/2/3/4/5/6/7
14.5.2. Master Receiver Mode
Serial data is received on SDA while the serial clock is output on SCL. The SMBus interface generates the
START condition and transmits the first byte containing the address of the target slave and the data direc-
tion bit. In this case the data direction bit (R/W) will be logic 1 (READ). Serial data is then received from the
slave on SDA while the SMBus outputs the serial clock. The slave transmits one or more bytes of serial
data. After each byte is received, ACKRQ is set to ‘1’ and an interrupt is generated. Software must write
the ACK bit (SMB0CN.1) to define the outgoing acknowledge value (Note: writing a ‘1’ to the ACK bit gen-
erates an ACK; writing a ‘0’ generates a NACK). Software should write a ‘0’ to the ACK bit after the last
byte is received, to transmit a NACK. The interface exits Master Receiver Mode after the STO bit is set and
a STOP is generated. Note that the interface will switch to Master Transmitter Mode if SMB0DAT is written
while an active Master Receiver. Figure 14.6 shows a typical Master Receiver sequence. Two received
data bytes are shown, though any number of bytes may be received. Notice that the ‘data byte transferred’
interrupts occur before the ACK cycle in this mode.
158
Interrupt
S
Figure 14.6. Typical Master Receiver Sequence
Received by SMBus
Interface
Transmitted by
SMBus Interface
SLA
R
Interrupt
A
Data Byte
Rev. 1.7
Interrupt
A
S = START
P = STOP
A = ACK
N = NACK
R = READ
SLA = Slave Address
Data Byte
Interrupt
N
P