C8051F044-GQ Silicon Laboratories Inc, C8051F044-GQ Datasheet - Page 122

• Manufacturer Part Number: C8051F044-GQ
• Description: IC 8051 MCU 64K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F044-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 100-TQFP, 100-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: CAN/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F040DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• On-chip Dac: 2-ch x 12-bit
• No. Of I/o's: 64
• Ram Memory Size: 4352Byte
• Cpu Speed: 25MHz
• No. Of Timers: 5
• Rohs Compliant: Yes
• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F04x
• Maximum Speed: 25 MHz
• Data Rom Size: 64 KB
• A/d Bit Size: 10 bit
• A/d Channels Available: 13
• Height: 1 mm
• Length: 14 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 14 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1209

C8051F040/1/2/3/4/5/6/7
The hysteresis of the Comparator is software-programmable via its Comparator Control register (CPT-
nCN). The user can program both the amount of hysteresis voltage (referred to the input voltage) and the
positive and negative-going symmetry of this hysteresis around the threshold voltage.
The Comparator hysteresis is programmed using Bits3-0 in the Comparator Control Register CPTnCN
(shown in SFR Definition 11.1). The amount of negative hysteresis voltage is determined by the settings of
the CPnHYN bits. As shown in Table 11.1, settings of approximately 20, 10 or 5 mV of negative hysteresis
can be programmed, or negative hysteresis can be disabled. In a similar way, the amount of positive hys-
teresis is determined by the setting the CPnHYP bits.
Comparator interrupts can be generated on either rising-edge and falling-edge output transitions. (For
Interrupt enable and priority control, see
or falling -edge interrupts are enabled using the comparator’s Rising/Falling Edge Interrupt Enable Bits
(CPnRIE and CPnFIE) in their respective Comparator Mode Selection Register (CPTnMD), shown in SFR
Definition 11.2. These bits allow the user to control which edge (or both) will cause a comparator interrupt.
However, the comparator interrupt must also be enabled in the Extended Interrupt Enable Register (EIE1).
The CPnFIF flag is set to logic 1 upon a Comparator falling-edge interrupt, and the CPnRIF flag is set to
logic 1 upon the Comparator rising-edge interrupt. Once set, these bits remain set until cleared by soft-
ware. The output state of a Comparator can be obtained at any time by reading the CPnOUT bit. A Com-
parator is enabled by setting its respective CPnEN bit to logic 1, and is disabled by clearing this bit to logic
0.Upon enabling a comparator, the output of the comparator is not immediately valid. Before using a com-
parator as an interrupt or reset source, software should wait for a minimum of the specified “Power-up
time” as specified in Table 11.1, “Comparator Electrical Characteristics,” on page 126.
122
(Programmed with CPnHYP Bits)
Positive Hysteresis Voltage
INPUTS
OUTPUT
VIN+
VIN-
CIRCUIT CONFIGURATION
Positive Hysteresis
CPn-
CPn+
VIN+
VIN-
Disabled
V
OL
Figure 11.2. Comparator Hysteresis Plot
V
OH
+
_
CPn
Section “12.3. Interrupt Handler” on page
Positive Hysteresis
Maximum
OUT
Rev. 1.5
Negative Hysteresis
Disabled
Negative Hysteresis
(Programmed by CPnHYN Bits)
Maximum
Negative Hysteresis Voltage
153). The rising and/