C8051F005-GQ Silicon Laboratories Inc, C8051F005-GQ Datasheet - Page 29

• Manufacturer Part Number: C8051F005-GQ
• Description: IC 8051 MCU 32K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F00xr

Specifications of C8051F005-GQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 64-TQFP, 64-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• On-chip Dac: 2-ch x 12-bit
• No. Of I/o's: 32
• Ram Memory Size: 2304Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1188 - DEV KIT FOR F005/006/007
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1187

5. ADC (12-Bit, C8051F000/1/2/5/6/7 Only)
The ADC subsystem for the C8051F000/1/2/5/6/7 consists of a 9-channel, configurable analog multiplexer
(AMUX), a programmable gain amplifier (PGA), and a 100ksps, 12-bit successive-approximation-register ADC
with integrated track-and-hold and programmable window detector (see block diagram in Figure 5.1). The AMUX,
PGA, Data Conversion Modes, and Window Detector are all configurable under software control via the Special
Function Register’s shown in Figure 5.1. The ADC subsystem (ADC, track-and-hold and PGA) is enabled only
when the ADCEN bit in the ADC Control register (ADC0CN, Figure 5.7) is set to 1. The ADC subsystem is in low
power shutdown when this bit is 0. The Bias Enable bit (BIASE) in the REF0CN register (see Figure 9.2) must be
set to 1 in order to supply bias to the ADC.
5.1.
Eight of the AMUX channels are available for external measurements while the ninth channel is internally
connected to an on-board temperature sensor (temperature transfer function is shown in Figure 5.3). Note that the
PGA gain is applied to the temperature sensor reading. AMUX input pairs can be programmed to operate in either
the differential or single-ended mode. This allows the user to select the best measurement technique for each input
channel, and even accommodates mode changes “on-the-fly”. The AMUX defaults to all single-ended inputs upon
reset. There are two registers associated with the AMUX: the Channel Selection register AMX0SL (Figure 5.5),
and the Configuration register AMX0CF (Figure 5.4). The table in Figure 5.5 shows AMUX functionality by
channel for each possible configuration. The PGA amplifies the AMUX output signal by an amount determined by
the AMPGN2-0 bits in the ADC Configuration register, ADC0CF (Figure 5.6). The PGA can be software-
programmed for gains of 0.5, 1, 2, 4, 8 or 16. It defaults to unity gain on reset.
29
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
Analog Multiplexer and PGA
SENSOR
AGND
TEMP
AMX0CF
ADC0GTH
Figure 5.1. 12-Bit ADC Functional Block Diagram
+
+
+
+
-
-
-
-
AMUX
(SE or
9-to-1
DIFF)
AMX0SL
ADC0GTL
X
+
-
AV+
ADCEN
Rev. 1.7
AGND
ADC0CF
ADC0LTH
ADC
12-Bit
AV+
SAR
ADC0CN
ADC0LTL
12
24
12
COMB
LOGIC
ADWINT