PIC24HJ32GP202-I/SP Microchip Technology, PIC24HJ32GP202-I/SP Datasheet - Page 2

• Manufacturer Part Number: PIC24HJ32GP202-I/SP
• Description: IC PIC MCU FLASH 32K 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ32GP202-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 32KB (11K x 24)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM300027
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164337 - MODULE SOCKET FOR PM3 40DIP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24HJ32GP202/204 and PIC24HJ16GP304
TABLE 2:
DS80467E-page 2
Note 1:
Identification
Operations
Regulator
Module
Product
Internal
Voltage
UART
UART
UART
UART
UART
UART
UART
UART
JTAG
I
PSV
2
SPI
I
I
C™
2
2
C
C
Only those issues indicated in the last column apply to the current silicon revision.
SILICON ISSUE SUMMARY
Programming
Temperature
High-Speed
High-Speed
Sleep Mode
SFR Writes
Addressing
Addressing
Auto-Baud
Auto-Baud
Auto-Baud
SCKx Pins
Extended
Interrupts
IR Mode
IR Mode
Feature
Flash
Mode
Mode
10-bit
10-bit
—
Number
Item
10.
11.
12.
13.
14.
15.
16.
1.
2.
3.
4.
5.
6.
7.
8.
9.
JTAG programming does not work.
The auto-baud feature may not calculate the cor-
rect baud rate when the Baud Rate Generator
(BRG) is set up for 4x mode.
With the auto-baud feature selected, the Sync
Break character (0x55) may be loaded into the
FIFO as data.
The auto-baud feature measures baud rate inaccu-
rately for certain baud rate and clock speed combi-
nations.
When an auto-baud is detected, the receive inter-
rupt may occur twice.
The 16x baud clock signal on the BCLK pin is pres-
ent only when the module is transmitting.
When the UART is in 4x mode (BRGH = 1) and
using two Stop bits (STSEL = 1), it may sample the
first Stop bit instead of the second one.
The SPIxCON1 DISSCK bit does not influence port
functionality.
The BCL bit in I2CSTAT can be cleared only with
16-bit operation and can be corrupted with 1-bit or
8-bit operations on I2CSTAT.
When the I
addressing using the same address bits (A10 and
A9) as other I
work as expected.
Revision A2 devices marked as extended temper-
ature range (E) devices, support only industrial
temperature range (I).
The UART error interrupt may not occur, or may
occur at an incorrect time, if multiple errors occur
during a short period of time.
When the UART module is operating in 8-bit mode
(PDSEL = 0x) and using the IrDA
decoder (IREN = 1), the module incorrectly trans-
mits a data payload of 80h as 00h.
When the VREGS bit (RCON<8>) is set to a logic
‘0’, device may Reset and higher sleep current
may be observed.
An address error trap occurs in certain addressing
modes when accessing the first four bytes of any
PSV page.
When the I
slave with and address of 0x102, the I2CxRCV
register content for the lower address byte is 0x01
rather than 0x02.
2
2
C module is configured for 10-bit
C module is configured as a 10-bit
2
C device A10 and A9 bits may not
Issue Summary
®
encoder/
© 2010 Microchip Technology Inc.
Affected Revisions
A2 A3 A4 A5 A6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
(1)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X