PIC16F631-I/SS Microchip Technology, PIC16F631-I/SS Datasheet - Page 179

• Manufacturer Part Number: PIC16F631-I/SS
• Description: IC PIC MCU FLASH 1KX14 20SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F631-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 20-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 18
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 658-1047-5 - BOARD EVALUATION ACCESSTOUCHXLT20SS1-1 - SOCKET TRANSITION 20DIP 20SSOPXLT20SS-1 - SOCKET TRANSITION 18DIP 20SSOPAC162061 - HEADER INTRFC MPLAB ICD2 20PINAC164307 - MODULE SKT FOR PM3 28SSOP
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

REGISTER 13-2:
© 2006 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3-0
Note 1: PIC16F687/PIC16F689/PIC16F690 only.
WCOL
R/W-0
2: When this mode is selected, any reads or writes to the SSPADD SFR address actually accesses the SSPMSK register.
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software)
0 = No collision
SSPOV: Receive Overflow Indicator bit
In SPI mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the
0 = No overflow
In I
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a “don’t care” in
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
In SPI mode:
1 = Enables serial port and configures SCK, SDO and SDI as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In I
1 = Enables the serial port and configures the SDA and SCL pins as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In both modes, when enabled, these pins must be properly configured as input or output.
CKP: Clock Polarity Select bit
In SPI mode:
1 = Idle state for clock is a high level (Microwire default)
0 = Idle state for clock is a low level (Microwire alternate)
In I
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch). (Used to ensure data setup time.)
SSPM<3:0>: Synchronous Serial Port Mode Select bits
0000 = SPI Master mode, clock = F
0001 = SPI Master mode, clock = F
0010 = SPI Master mode, clock = F
0011 = SPI Master mode, clock = TMR2 output/2
0100 = SPI Slave mode, clock = SCK pin. SS pin control enabled.
0101 = SPI Slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin.
0110 = I
0111 = I
1000 = Reserved
1001 = Load SSPMSK register at SSPADD SFR address
1010 = Reserved
1011 = I
1100 = Reserved
1101 = Reserved
1110 = I
1111 = I
2
2
2
SSPOV
R/W-0
C™ mode:
C mode:
C mode:
data in SSPSR is lost. Overflow can only occur in Slave mode. The user must read the SSPBUF, even if only
transmitting data, to avoid setting overflow. In Master mode, the overflow bit is not set since each new recep-
tion (and transmission) is initiated by writing to the SSPBUF register.
Transmit mode. SSPOV must be cleared in software in either mode.
SSPCON: SYNC SERIAL PORT CONTROL REGISTER
2
2
2
2
2
C Slave mode, 7-bit address
C Slave mode, 10-bit address
C Firmware Controlled Master mode (slave IDLE)
C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
W = Writable bit
‘1’ = Bit is set
SSPEN
R/W-0
PIC16F631/677/685/687/689/690
OSC
OSC
OSC
R/W-0
CKP
Preliminary
/4
/16
/64
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPM3
R/W-0
(2)
(2)
SSPM2
R/W-0
(2)
(1)
x = Bit is unknown
SSPM1
R/W-0
(2)
DS41262C-page 177
SSPM0
R/W-0
(2)
bit 0