ATTINY84V-10SSUR Atmel, ATTINY84V-10SSUR Datasheet - Page 52

• Manufacturer Part Number: ATTINY84V-10SSUR
• Description: MCU AVR 8KB FLASH 10MHZ 14SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY84V-10SSUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.3.3
9.3.4
52
ATtiny24/44/84
GIFR – General Interrupt Flag Register
PCMSK1 – Pin Change Mask Register 1
• Bit 4 – PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 0 is enabled. Any change on any enabled PCINT7:0 pin will cause an interrupt.
The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI0 Inter-
rupt Vector. PCINT7:0 pins are enabled individually by the PCMSK0 Register.
• Bits 7, 3:0 – Res: Reserved Bits
These bits are reserved in the ATtiny24/44/84 and will always read as zero.
• Bit 6 – INTF0: External Interrupt Flag 0
When an edge or logic change on the INT0 pin triggers an interrupt request, INTF0 becomes set
(one). If the I-bit in SREG and the INT0 bit in GIMSK are set (one), the MCU will jump to the cor-
responding Interrupt Vector. The flag is cleared when the interrupt routine is executed.
Alternatively, the flag can be cleared by writing a logical one to it. This flag is always cleared
when INT0 is configured as a level interrupt.
• Bit 5 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT11:8 pin triggers an interrupt request, PCIF1 becomes set
(one). If the I-bit in SREG and the PCIE1 bit in GIMSK are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 4 – PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7:0 pin triggers an interrupt request, PCIF becomes set
(one). If the I-bit in SREG and the PCIE0 bit in GIMSK are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bits 7:4 – Res: Reserved Bits
These bits are reserved in the ATtiny24/44/84 and will always read as zero.
• Bits 3:0 – PCINT11:8: Pin Change Enable Mask 11:8
Each PCINT11:8 bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT11:8 is set and the PCIE1 bit in GIMSK is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT11:8 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
Bit
0x3A (0x5A
Read/Write
Initial Value
Bit
0x20 (0x40)
Read/Write
Initial Value
R
7
–
0
R
7
–
0
INTF0
R
R/W
6
–
0
6
0
R
PCIF1
5
–
0
R/W
5
0
R
4
–
0
PCIF0
R/W
4
0
PCINT11
R/W
3
0
R
3
–
0
PCINT10
R/W
2
0
R
2
–
0
PCINT9
R/W
1
0
R
1
–
0
PCINT8
R/W
0
–
R
0
0
0
8006K–AVR–10/10
PCMSK1
GIFR