PIC18LF2410T-I/SO Microchip Technology, PIC18LF2410T-I/SO Datasheet - Page 3

• Manufacturer Part Number: PIC18LF2410T-I/SO
• Description: IC MCU FLASH 8KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF2410T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

REGISTER 17-3:
© 2007 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
ABDOVF
R/W-0
ABDOVF: Auto-Baud Acquisition Rollover Status bit
1 = A BRG rollover has occurred during Auto-Baud Rate Detect mode
0 = No BRG rollover has occurred
RCIDL: Receive Operation Idle Status bit
1 = Receive operation is Idle
0 = Receive operation is Active
RXDTP: Receive Data Polarity Select bit
Asynchronous mode:
1 = Receive data (RX) is inverted. Idle state is a low level.
0 = No inversion of receive data (RX). Idle state is a high level.
Synchronous mode:
1 = Data (DT) is inverted. Idle state is a low level.
0 = No inversion of data (DT). Idle state is a high level.
TXCKP: Transmit/Clock Polarity Select bit
Asynchronous mode:
1 = Transmit data (TX) is inverted. Idle state is a low level.
0 = No inversion of transmit data (TX). Idle state is a high level.
Synchronous mode:
1 = Idle state for clock (CK) is a high level
0 = Idle state for clock (CK) is a low level
BRG16: 16-bit Baud Rate Register Enable bit
1 = 16-bit Baud Rate Generator – SPBRGH and SPBRG
0 = 8-bit Baud Rate Generator – SPBRG only (Compatible mode); SPBRGH value ignored
Unimplemented: Read as ‘0’
WUE: Wake-up Enable bit
Asynchronous mode:
1 = EUSART will continue to sample the RX pin with the interrupt generated on the falling edge; bit
0 = RX pin is not monitored or rising edge detected
Synchronous mode:
Unused in this mode.
ABDEN: Auto-Baud Detect Enable bit
Asynchronous mode:
1 = Enable baud rate measurement on the next character. Requires reception of a Sync field (55h);
0 = Baud rate measurement disabled or completed
Synchronous mode:
Unused in this mode.
RCIDL
R-1
(must be cleared in software)
cleared in hardware on following rising edge
cleared in hardware upon completion.
BAUDCON: BAUD RATE CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
RXDTP
R/W-0
PIC18F2410/2510/4410/4510
TXCKP
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
BRG16
R/W-0
U-0
—
x = Bit is unknown
R/W-0
WUE
DS80314B-page 3
ABDEN
R/W-0
bit 0