ATMEGA8A-AU Atmel, ATMEGA8A-AU Datasheet - Page 29

• Manufacturer Part Number: ATMEGA8A-AU
• Description: MCU AVR 8K FLASH 16MHZ 32-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8A-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.6
8159D–AVR–02/11
Calibrated Internal RC Oscillator
The calibrated internal RC Oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0MHz clock. All frequen-
cies are nominal values at 5V and 25°C. This clock may be selected as the system clock by
programming the CKSEL Fuses as shown in
nal components. The CKOPT Fuse should always be unprogrammed when using this clock
option. During reset, hardware loads the 1MHz calibration byte into the OSCCAL Register and
thereby automatically calibrates the RC Oscillator. At 5V, 25°C and 1.0MHz Oscillator frequency
selected, this calibration gives a frequency within ± 3% of the nominal frequency. Using run-time
calibration methods as described in application notes available at www.atmel.com/avr it is possi-
ble to achieve ± 1% accuracy at any given V
as the chip clock, the Watchdog Oscillator will still be used for the Watchdog Timer and for the
Reset Time-out. For more information on the pre-programmed calibration value, see the section
“Calibration Byte” on page
Table 8-8.
Note:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table
pins or Timer Oscillator pins:
Table 8-9.
Note:
SUT1:0
10
00
01
11
8-9. PB6 (XTAL1/TOSC1) and PB7(XTAL2/TOSC2) can be used as either general I/O
(1)
1. The device is shipped with this option selected.
1. The device is shipped with this option selected.
CKSEL3:0
Internal Calibrated RC Oscillator Operating Modes
Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
0001
Power-down and Power-
0010
0011
0100
Start-up Time from
(1)
save
6 CK
6 CK
6 CK
228.
Additional Delay from
CC
Table
(V
and Temperature. When this Oscillator is used
CC
4.1 ms
Reserved
Reset
65 ms
8-8. If selected, it will operate with no exter-
= 5.0V)
–
Nominal Frequency (MHz)
1.0
2.0
4.0
8.0
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
ATmega8A
29