AT32UC3L064-AUT Atmel, AT32UC3L064-AUT Datasheet - Page 86

• Manufacturer Part Number: AT32UC3L064-AUT
• Description: MCU AVR32 64KB FLASH 48TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L064-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI/TWI/USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 9-ch x 10-bit
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 50 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

10.2.6
10.2.7
10.2.8
32099F–11/2010
WDT
GPIO
SPI
1. Clearing the Watchdog Timer (WDT) counter in second half of timeout period will
1. Clearing GPIO interrupt may fail
1. SPI disable does not work in SLAVE mode
2. SPI bad serial clock generation on 2nd chip select when SCBR==1, CPOL==1, and
3. SPI data transfer hangs with CSR0.CSAAT==1 and MR.MODFDIS==0
4. Disabling SPI has no effect on the SR.TDRE bit
After writing to the Status Clear Register (SCR) the wake signal is released one AST clock
cycle after the BUSY bit in the Status Register (SR.BUSY) is cleared. If entering sleep mode
directly after the BUSY bit is cleared the part will wake up immediately.
Fix/Workaround
Read the Wake Enable Register (WER) and write this value back to the same register. Wait
for BUSY to clear before entering sleep mode.
issue a Watchdog reset
If the WDT counter is cleared in the second half of the timeout period, the WDT will immedi-
ately issue a Watchdog reset.
Fix/Workaround
Use twice as long timeout period as needed and clear the WDT counter within the first half
of the timeout period. If the WDT counter is cleared after the first half of the timeout period,
you will get a Watchdog reset immediately. If the WDT counter s not cleared at all, the time
before the reset will be twice as long as needed.
Writing a one to the GPIO.IFRC register to clear the interrupt will be ignored if interrupt is
enabled for the corresponding port.
Fix / Workaround
Disable the interrupt, clear the interrupt by writing a one to GPIO.IFRC, then enable the
interrupt.
SPI disable does not work in SLAVE mode.
Fix/Workaround
Read the last received data, then perform a software reset by writing a one to the Software
Reset bit in the Control Register (CR.SWRST).
NCPHA==0
W h e n m u l t i p l e c h i p s e l e c t s a r e i n u s e , i f o n e o f t h e b a u d r a t e s i s e q u a l t o 1
(CSRn.SCBR==1) and one of the others is not equal to 1, and CSRn.CPOL==1 and
CSRn.NCPHA==0, an additional pulse will be generated on SCK.
Fix/Workaround
When multiple chip selects are in use, if one of the baudrates is equal to 1, the others must
also be equal to 1 if CSRn.CPOL==1 and CSRn.NCPHA==0.
When CSR0.CSAAT==1 and mode fault detection is enabled (MR.MODFDIS==0), the SPI
module will not start a data transfer.
Fix/Workaround
Disable mode fault detection by writing a one to MR.MODFDIS.
Disabling SPI has no effect on SR.TDRE whereas the write data command is filtered when
SPI is disabled. This means that as soon as the SPI is disabled it becomes impossible to
AT32UC3L016/32/64
86