DSPIC33FJ128GP802-I/SO Microchip Technology, DSPIC33FJ128GP802-I/SO Datasheet - Page 187

IC DSPIC MCU/DSP 128K 28SOIC

DSPIC33FJ128GP802-I/SO

Manufacturer Part Number
DSPIC33FJ128GP802-I/SO
Description
IC DSPIC MCU/DSP 128K 28SOIC
Manufacturer
Microchip Technology
Series
dsPIC™ 33Fr

Specifications of DSPIC33FJ128GP802-I/SO

Program Memory Type
FLASH
Program Memory Size
128KB (128K x 8)
Package / Case
28-SOIC (7.5mm Width)
Core Processor
dsPIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART
Peripherals
AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
Number Of I /o
21
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 10x10b/12b, D/A 4x16b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Product
DSCs
Data Bus Width
16 bit
Processor Series
DSPIC33F
Core
dsPIC
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
21
Data Ram Size
16 KB
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
12.0
The Timer1 module is a 16-bit timer, which can serve
as the time counter for the real-time clock, or operate
as a free-running interval timer/counter.
The Timer1 module has the following unique features
over other timers:
• Can be operated from the low power 32 kHz
• Can be operated in Asynchronous Counter mode
• The external clock input (T1CK) can optionally be
FIGURE 12-1:
 2009 Microchip Technology Inc.
dsPIC33FJ32GP302/304, dsPIC33FJ64GPX02/X04, AND dsPIC33FJ128GPX02/X04
crystal oscillator available on the device
from an external clock source.
synchronized to the internal device clock and the
clock synchronization is performed after the
prescaler.
Note 1: This data sheet summarizes the features
SOSCO/
SOSCI
T1CK
Note 1: Refer to Section 9.0 “Oscillator Configuration” for information on enabling the secondary oscillator.
2: Some registers and associated bits
TIMER1
of
dsPIC33FJ64GPX02/X04,
dsPIC33FJ128GPX02/X04 families of
devices. It is not intended to be a compre-
hensive reference source. To comple-
ment the information in this data sheet,
refer to “Section 11. Timers” (DS70205)
of the “dsPIC33F/PIC24H Family Refer-
ence Manual”, which is available from the
Microchip website (www.microchip.com).
described in this section may not be avail-
able on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
the
LPOSCEN
16-BIT TIMER1 MODULE BLOCK DIAGRAM
dsPIC33FJ32GP302/304,
(1)
F
TCKPS<1:0>
Prescaler
CY
(/n)
TCKPS<1:0>
Prescaler
Sync
Gate
(/n)
and
Sync
Preliminary
TSYNC
Falling Edge
Detect
1
0
TGATE
The unique features of Timer1 allow it to be used for
Real-Time Clock (RTC) applications. A block diagram
of Timer1 is shown in Figure 12-1.
The Timer1 module can operate in one of the following
modes:
• Timer mode
• Gated Timer mode
• Synchronous Counter mode
• Asynchronous Counter mode
In Timer and Gated Timer modes, the input clock is
derived from the internal instruction cycle clock (F
In Synchronous and Asynchronous Counter modes,
the input clock is derived from the external clock input
at the T1CK pin.
The Timer modes are determined by the following bits:
• Timer Clock Source Control bit (TCS): T1CON<1>
• Timer Synchronization Control bit (TSYNC):
• Timer Gate Control bit (TGATE): T1CON<6>
Timer control bit setting for different operating modes
are given in the Table 12-1.
TABLE 12-1:
Timer
Gated timer
Synchronous
counter
Asynchronous
counter
TCS
T1CON<2>
Mode
10
00
x1
Comparator
TIMER MODE SETTINGS
TMR1
PR1
TCS
0
0
1
1
Reset
Equal
TGATE
TGATE
0
1
x
x
DS70292D-page 187
1
0
Set T1IF flag
TSYNC
x
x
1
0
CY
).

Related parts for DSPIC33FJ128GP802-I/SO