PIC17C756A-33I/PT Microchip Technology, PIC17C756A-33I/PT Datasheet - Page 84

• Manufacturer Part Number: PIC17C756A-33I/PT
• Description: IC MCU OTP 16KX16 A/D PWM 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17C756A-33I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 33MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 50
• Program Memory Type: OTP
• Ram Size: 902 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC17
• No. Of I/o's: 50
• Ram Memory Size: 902Byte
• Cpu Speed: 33MHz
• No. Of Timers: 4
• Processor Series: PIC17C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 902 B
• Interface Type: I2C, MSSP, RS- 232, SCI, SPI, USART
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 8
• Operating Supply Voltage: 3 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC17C7XX
10.6
PORTF is an 8-bit wide bi-directional port. The corre-
sponding data direction register is DDRF. A ’1’ in DDRF
configures the corresponding port pin as an input. A ’0’
in the DDRF register configures the corresponding port
pin as an output. Reading PORTF reads the status of
the pins, whereas writing to PORTF will write to the
respective port latch.
All eight bits of PORTF are multiplexed with 8 channels
of the 10-bit A/D converter.
Upon RESET, the entire Port is automatically config-
ured as analog inputs and must be configured in soft-
ware to be a digital I/O.
FIGURE 10-13:
DS30289B-page 84
Note: I/O pins have protection diodes to V
WR PORTF
WR DDRF
RD PORTF
Data Bus
V
AIN
PORTF and DDRF Registers
PCFG3:PCFG0
CHS3:CHS0
BLOCK DIAGRAM OF RF7:RF0
Data Latch
DDRF Latch
D
CK
D
CK
RD DDRF
Q
Q
Q
Q
DD
and V
SS
Q
.
EN
EN
D
Example 10-6 shows an instruction sequence to initial-
ize PORTF. The Bank Select Register (BSR) must be
selected to Bank 5 for the port to be initialized. The fol-
lowing example uses the MOVLB instruction to load the
BSR register for bank selection.
EXAMPLE 10-6:
To other pads
To other pads
MOVLB
MOVWF
MOVWF
CLRF
MOVLW
MOVWF
5
0x0E
ADCON1
PORTF, F
0x03
DDRF
V
V
P
N
DD
SS
INITIALIZING PORTF
; Select Bank 5
; Configure PORTF as
; Digital
; Initialize PORTF data
;
;
;
; Value used to init
;
; Set RF<1:0> as inputs
;
2000 Microchip Technology Inc.
latches before
the data direction
register
data direction
RF<7:2> as outputs
ST
Input
Buffer
I/O pin