C8051F504-IQ Silicon Laboratories Inc, C8051F504-IQ Datasheet - Page 180

• Manufacturer Part Number: C8051F504-IQ
• Description: IC 8051 MCU 32K FLASH 48-QFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F50xr

Specifications of C8051F504-IQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-QFP
• Mfg Application Notes: LIN Bootloader AppNote
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), CAN, LIN, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 40
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 32x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 40
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F500DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 32-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1527 - KIT DEV FOR C8051F50X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1518

C8051F50x/F51x
20.2.3. Assigning Port I/O Pins to External Digital Event Capture Functions
External digital event capture functions can be used to trigger an interrupt or wake the device from a low
power mode when a transition occurs on a digital I/O pin. The digital event capture functions do not require
dedicated pins and will function on both GPIO pins (PnSKIP = 1) and pins in use by the Crossbar (PnSKIP
= 0). External digital event capture functions cannot be used on pins configured for analog I/O. Table 20.3
shows all available external digital event capture functions.
20.3. Priority Crossbar Decoder
The Priority Crossbar Decoder (Figure 20.3) assigns a priority to each I/O function, starting at the top with
UART0. When a digital resource is selected, the least-significant unassigned Port pin is assigned to that
resource excluding UART0, which is always assigned to pins P0.4 and P0.5, and excluding CAN0 which is
always assigned to pins P0.6 and P0.7. If a Port pin is assigned, the Crossbar skips that pin when assign-
ing the next selected resource. Additionally, the Crossbar will skip Port pins whose associated bits in the
PnSKIP registers are set. The PnSKIP registers allow software to skip Port pins that are to be used for
analog input, dedicated functions, or GPIO.
Because of the nature of Priority Crossbar Decoder, not all peripherals can be located on all port pins.
Figure 20.3 maps peripherals to the potential port pins on which the peripheral I/O can appear.
Important Note on Crossbar Configuration: If a Port pin is claimed by a peripheral without use of the
Crossbar, its corresponding PnSKIP bit should be set. This applies to P0.0 if VREF is used, P0.1 if the
ADC is configured to use the external conversion start signal (CNVSTR), P0.3 and/or P0.2 if the external
oscillator circuit is enabled, and any selected ADC or Comparator inputs. The Crossbar skips selected pins
as if they were already assigned, and moves to the next unassigned pin.
180
Digital Function
External Interrupt 0
External Interrupt 1
Port Match
*Note: P3.1–P3.7 are only available on the 48-pin packages.
Table 20.3. Port I/O Assignment for External Digital Event Capture Functions
Potentially Assignable Port Pins
Rev. 1.2
P0.0–P3.7*
P1.0–P1.7
P1.0–P1.7
P0MASK, P0MAT
P1MASK, P1MAT
P2MASK, P2MAT
P3MASK, P3MAT
SFR(s) used for
Assignment
IT01CF
IT01CF