MAXQ610A-0000+ Maxim Integrated Products, MAXQ610A-0000+ Datasheet - Page 21

• Manufacturer Part Number: MAXQ610A-0000+
• Description: IC MCU 16BIT 64K IR MOD 32TQFN
• Manufacturer: Maxim Integrated Products
• Series: MAXQ™r

Specifications of MAXQ610A-0000+

• Core Processor: RISC
• Core Size: 16-Bit
• Speed: 12MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Infrared, Power-Fail, POR, WDT
• Number Of I /o: 20
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 32-TQFN Exposed Pad
• Processor Series: MAXQ610
• Core: RISC
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: SPI, USART
• Maximum Clock Frequency: 12 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 1.7 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Controller Family/series: MAXQ
• No. Of I/o's: 24
• Ram Memory Size: 2048Byte
• Cpu Speed: 12MHz
• No. Of Timers: 2
• Embedded Interface Type: JTAG, SPI, USART
• Rohs Compliant: Yes
• Number Of Programmable I/os: 32
• Development Tools By Supplier: MAXQ610-KIT
• Package: 32TQFN EP
• Family Name: MAXQ
• Maximum Speed: 12 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 90-M6800+B01

The lowest power mode of operation for the MAXQ610
is stop mode. In this mode, CPU state and memories
are preserved, but the CPU is not actively running.
Wake-up sources include external I/O interrupts, the
power-fail warning interrupt, or a power-fail reset. Any
time the microcontroller is in a state where code does
not need to be executed, the user software can put the
MAXQ610 into stop mode. The nanopower ring oscilla-
tor is an internal ultra-low-power (400nA), 8kHz ring
oscillator that can be used to drive a wake-up timer that
exits stop mode. The wake-up timer is programmable
by software in steps of 125µs up to approximately 8s.
The power-fail monitor is always on during normal oper-
ation. However, it can be selectively disabled during
stop mode to minimize power consumption. This fea-
ture is enabled using the power-fail monitor disable
Figure 11. Power-Fail Detection During Normal Operation
INTERNAL RESET
(ACTIVE HIGH)
V
V
V
PFW
POR
RST
16-Bit Microcontroller with Infrared Module
V
DD
______________________________________________________________________________________
A
B
C
Operating Modes
t < t
D
PFW
t ≥ t
PFW
E
(PFD) bit in the PWCN register. The reset default state
for the PFD bit is 1, which disables the power-fail moni-
tor function during stop mode. If power-fail monitoring
is disabled (PFD = 1) during stop mode, the circuitry
responsible for generating a power-fail warning or reset
is shut down and neither condition is detected. Thus,
the V
However, in the event that V
level, a POR is generated. The power-fail monitor is
enabled prior to stop mode exit and before code exe-
cution begins. If a power-fail warning condition (V
V
set on stop mode exit. If a power-fail condition is
detected (V
Figures 11, 12, and 13 show the power-fail detection
and response during normal and stop mode operation.
PFW
DD
) is then detected, the power-fail interrupt flag is
t ≥ t
PFW
F
< V
DD
RST
< V
condition does not invoke a reset state.
RST
), the CPU goes into reset.
G
Power-Fail Detection
t ≥ t
DD
PFW
falls below the POR
H
I
DD
21
<