DS5000T-32-16 Maxim Integrated Products, DS5000T-32-16 Datasheet - Page 3

• Manufacturer Part Number: DS5000T-32-16
• Description: IC MPU W/RTC 32KB 16MHZ 40-DIP
• Manufacturer: Maxim Integrated Products
• Series: DS500xr

Specifications of DS5000T-32-16

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: Power-Fail Reset, WDT
• Number Of I /o: 32
• Program Memory Type: SRAM
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 4.75 V ~ 5.25 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP Module (600 mil), 40-EDIP
• Processor Series: DS5000T
• Core: 8051
• Data Bus Width: 8 bit
• Program Memory Size: 32 KB
• Data Ram Size: 32 KB
• Interface Type: 3-Wire, RS-232, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 2
• Operating Supply Voltage: 4.75 V to 5.25 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: DS5000TK
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Other names: DS5000T3216

PIN DESCRIPTION
18, 19
21–28
32-39
PIN
1–8
10
11
12
13
14
15
16
17
20
29
30
31
40
9
P2.0–P2.7/
P0.7–P0.0/
AD7–AD0
P3.0/RXD
P3.2/INT0
P3.3/INT1
P1.0–P1.7
P3.1/TXD
P3.6/WR
P3.7/RD
XTAL2,
A8–A15
P3.4/T0
P3.5/T1
XTAL1
NAME
PSEN
GND
ALE
RST
V
EA
CC
General-Purpose I/O Port 1
Active-High Reset Input. A logic 1 applied to this pin will activate a reset state.
This pin is pulled down internally so this pin can be left unconnected if not used.
General-Purpose I/O Port Pin 3.0/Receive Signal for On-Board UART. This pin
should not be connected directly to a PC COM port.
General-Purpose I/O Port Pin 3.1/Transmit Signal for On-Board UART. This pin
should not be connected directly to a PC COM port.
General-Purpose I/O Port Pin 3.2/Active-Low External Interrupt 0
General-Purpose I/O Port Pin 3.3/Active-Low External Interrupt 1
General-Purpose I/O Port Pin 3.4/Timer 0 Input
General-Purpose I/O Port Pin 3.5/Timer 1 Input
General-Purpose I/O Port Pin 3.6/Active-Low Write Strobe for Expanded Bus
Operation
General-Purpose I/O Port Pin 3.7/Active-Low Read Strobe for Expanded Bus
Operation
Crystal Connection. Used to connect an external crystal to the internal oscillator.
XTAL1 is the input to an inverting amplifier and XTAL2 is the output.
Logic Ground
General-Purpose I/O Port 2/MSB of the Expanded Address Bus
Active-Low Program Store Enable. Used to enable an external program memory
when using the expanded bus. It is normally an output and should be unconnected
if not used. PSEN also is used to invoke the bootstrap loader. At this time, PSEN is
pulled down externally. This should only be done once the DS5000(T) is already in
a reset state. The device that pulls down should be open drain since it must not
interfere with PSEN under normal operation.
Address Latch Enable. Used to demultiplex the multiplexed expanded address/data
bus on Port 0. This pin is normally connected to the clock input on a ’373 type
transparent latch. When using a parallel programmer, this pin also assumes the
PROG function for programming pulses.
Active-Low External Access. This pin forces the DS5000(T) to behave like an
8031. No internal memory (or clock) is available when this pin is at a logic low.
Since this pin is pulled down internally, it should be connected to +5V to use NV
RAM. In a parallel programmer, this pin also serves as V
pulses.
General-Purpose I/O Port 0/Multiplexed Expanded Address/Data Bus. This port is
open drain and cannot drive a logic 1. It requires external pullups. When used in
the multiplexed expanded address data/bus mode, this pin does not require pullups.
+5V Power Supply
3 of 19
FUNCTION
PP
for super voltage