PIC16C433T-I/SO Microchip Technology, PIC16C433T-I/SO Datasheet - Page 11

• Manufacturer Part Number: PIC16C433T-I/SO
• Description: IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C433T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: LIN (Local Interconnect Network)
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 18-SOIC (7.5mm Width)
• For Use With: AC164030 - MODULE SKT PROMATEII 28DIP/SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

TABLE 3-1:
 2002 Microchip Technology Inc.
GP0/AN0
GP1/AN1/V
GP2/T0CKI/AN2/INT
GP3/MCLR/V
GP4/OSC2/AN3/CLKOUT
GP5/OSC1/CLKIN
LIN
V
BACT
V
V
AV
AV
Legend: I = Input, O = Output, I/O = Input/Output, P = Power, — = not used, TTL = TTL input,
BAT
DD
SS
DD
SS
ST = Schmitt Trigger input, OD = Open Drain
Name
REF
PP
PIC16C433 PINOUT DESCRIPTION
DIP Pin #
3,14,16
13
12
18
17
15
11
8
7
6
1
4
5
I/O/P
Type
I/O
I/O
I/O
I/O
I/O
I/O
O
P
P
P
P
P
I
TTL/ST Bi-directional I/O port/serial programming data/analog input
TTL/ST Bi-directional I/O port/serial programming clock/analog
TTL/ST Input port/Master Clear (Reset) input/programming voltage
TTL/ST Bi-directional IO port/oscillator crystal input/external clock
HV/OD High voltage bi-directional bus interface.
Buffer
Type
TTL
TTL
ST
Preliminary
—
—
—
—
—
0. Can be software programmed for internal weak pull-up
and interrupt-on-pin change. This buffer is a Schmitt Trig-
ger input when used in Serial Programming mode.
input 1/voltage reference. Can be software programmed for
internal weak pull-up and interrupt-on-pin change. This
buffer is a Schmitt Trigger input when used in Serial Pro-
gramming mode.
Bi-directional I/O port/analog input 2. Can be configured as
T0CKI or external interrupt.
input. When configured as MCLR, this pin is an active low
RESET to the device. Voltage on MCLR/V
exceed V
ware programmed for internal weak pull-up and interrupt-
on-pin change. Weak pull-up always on if configured as
MCLR. This buffer is Schmitt Trigger when in MCLR mode.
Bi-directional I/O port/oscillator crystal output/analog input
3. Connections to crystal or resonator in Crystal Oscillator
mode (HS, XT and LP modes only, GPIO in other modes).
In EXTRC and INTRC modes, the pin output can be config-
ured to CLKOUT, which has 1/4 the frequency of OSC1 and
denotes the instruction cycle rate.
source input (GPIO in INTRC mode only, OSC1 in all other
oscillator modes). Schmitt Trigger input for EXTRC Oscilla-
tor mode.
Battery input voltage.
Bus activity output pin. It is a CMOS-levels representation
of the LIN pin.
Positive supply for logic and I/O pins.
Ground reference for logic and I/O pins.
Analog positive supply.
Analog ground.
DD
during normal device operation. Can be soft-
Description
PIC16C433
PP
DS41139B-page 9
must not