ATMEGA649V-8AI Atmel, ATMEGA649V-8AI Datasheet - Page 167

• Manufacturer Part Number: ATMEGA649V-8AI
• Description: IC AVR MCU FLASH 64K 1.8V 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA649V-8AI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

18.5.2
18.5.3
2552K–AVR–04/11
SPSR – SPI Status Register
SPDR – SPI Data Register
• Bit 7 – SPIF: SPI Interrupt Flag
When a serial transfer is complete, the SPIF Flag is set. An interrupt is generated if SPIE in
SPCR is set and global interrupts are enabled. If SS is an input and is driven low when the SPI is
in Master mode, this will also set the SPIF Flag. SPIF is cleared by hardware when executing the
corresponding interrupt handling vector. Alternatively, the SPIF bit is cleared by first reading the
SPI Status Register with SPIF set, then accessing the SPI Data Register (SPDR).
• Bit 6 – WCOL: Write COLlision Flag
The WCOL bit is set if the SPI Data Register (SPDR) is written during a data transfer. The
WCOL bit (and the SPIF bit) are cleared by first reading the SPI Status Register with WCOL set,
and then accessing the SPI Data Register.
• Bit 5..1 – Reserved Bits
These bits are reserved bits in the ATmega329/3290/649/6490 and will always read as zero.
• Bit 0 – SPI2X: Double SPI Speed Bit
When this bit is written logic one the SPI speed (SCK Frequency) will be doubled when the SPI
is in Master mode (see
clock periods. When the SPI is configured as Slave, the SPI is only guaranteed to work at f
or lower.
The SPI interface on the ATmega329/3290/649/6490 is also used for program memory and
EEPROM downloading or uploading. See
The SPI Data Register is a read/write register used for data transfer between the Register File
and the SPI Shift Register. Writing to the register initiates data transmission. Reading the regis-
ter causes the Shift Register Receive buffer to be read.
Bit
0x2D (0x4D)
Read/Write
Initial Value
Bit
0x2E (0x4E)
Read/Write
Initial Value
SPIF
MSB
R/W
R
X
7
0
7
WCOL
R/W
Table
R
6
0
6
X
18-5). This means that the minimum SCK period will be two CPU
R/W
R
5
–
0
5
X
R/W
4
–
R
0
4
X
page 308
ATmega329/3290/649/6490
R/W
R
X
3
–
0
3
for serial programming and verification.
R/W
R
X
2
–
0
2
R/W
R
1
–
0
1
X
SPI2X
R/W
LSB
R/W
0
0
0
X
Undefined
SPSR
SPDR
osc
167
/4