AD8041ARZ Analog Devices Inc, AD8041ARZ Datasheet - Page 12

• Manufacturer Part Number: AD8041ARZ
• Description: IC OPAMP VF R-R LP LDIST 8SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD8041ARZ

• Slew Rate: 170 V/µs
• Amplifier Type: Voltage Feedback
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• -3db Bandwidth: 170MHz
• Current - Input Bias: 1.2µA
• Voltage - Input Offset: 2000µV
• Current - Supply: 5.8mA
• Current - Output / Channel: 50mA
• Voltage - Supply, Single/dual (±): 3 V ~ 12 V, ±1.5 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Op Amp Type: Voltage Feedback
• No. Of Amplifiers: 1
• Bandwidth: 170MHz
• Supply Voltage Range: 3V To 12V
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Gain Bandwidth Product: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD8041
Disable Operation
The AD8041 has an active-low disable pin, which can be used
to three-state the output of the part and also lower its supply
current. If the disable pin is left floating, the part is enabled and
will perform normally. If the disable pin is pulled to 2.5 V (min)
below the positive supply, output of the AD8041 will be disabled
and the nominal supply current will drop to less than 1.6 mA.
For best isolation, the disable pin should be pulled to as low a
voltage as possible; ideally, the negative supply rail.
The disable pin on the AD8041 allows it to be configured as a 2:1
mux as shown in Figure 7 and can be used to switch many types of
high speed signals. Higher order multiplexers can also be built.
The break-before-make switching time is approximately 50 ns to
disable the output and 300 ns to enable the output.
10MHz
5MHz
CH0
CH1
g
m
g
Vi
m
13
Vi
Figure 6. Small Signal Schematic
74HC04
12 11
Figure 7. 2:1 Multiplexer
R1
R1
330
330
S1N
S1P
C7
50
50
10
3
2
3
2
AD8041
AD8041
g
m2
8
8
5V
5V
7
7
C3
4
4
C9
R2
10 F
10 F
330
330
6
6
G = +2
G = +2
V
50
OUT
–12–
Single-Supply A/D Conversion
Figure 9 shows the AD8041 driving the analog inputs of the
AD9050 in a dc-coupled system with single-ended signals. All
components are powered from a single 5 V supply. The AD820
is used to offset the ground referenced input signal to the level
required by the AD9050. The AD8041 is used to add in the offset
with the ground referenced input signal and buffer the input to
AD9050. The nominal input range of the AD9050 is 2.8 V
and 3.8 V (1 V p-p centered at 3.3 V). This circuit provides
40 MSPS analog-to-digital conversion on just 330 mW of power
while delivering 10-bit performance.
–0.5V TO +0.5V
V
IN
–100
Figure 10. FFT Output of Circuit in Figure 9
Figure 9. 10-Bit, 40 MSPS A/D Conversion
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
Figure 8. 2:1 Multiplexer Performance
100
0%
90
10
0.1 F
1k
1k
V
1V
S
= 5V
1k
AD8041
1k
5V
AD820
F
FUNDAMENTAL = 0.6dB
SECOND HARMONIC = 66.9dB
THIRD HARMONIC = 74.7dB
SNR = 55.2dB
NOISE FLOOR = – 86.1dB
ENCODE FREQUENCY = 40MHz
1
5V
= 4.9MHz
2.8V – 3.8V
200ns
3.3V
9
10
0.1 F
AD9050
5V
REV. B