AMP01FX Analog Devices Inc, AMP01FX Datasheet - Page 12

• Manufacturer Part Number: AMP01FX
• Description: IC AMP INST PREC LN 120MA 18CDIP
• Manufacturer: Analog Devices Inc
• Type: Instrumentation Ampr

Specifications of AMP01FX

• Rohs Status: RoHS non-compliant
• Amplifier Type: Instrumentation
• Number Of Circuits: 1
• Slew Rate: 4.5 V/µs
• -3db Bandwidth: 570kHz
• Current - Input Bias: 2nA
• Voltage - Input Offset: 40µV
• Current - Supply: 3mA
• Current - Output / Channel: 120mA
• Voltage - Supply, Single/dual (±): ±4.5 V ~ 18 V
• Operating Temperature: -25°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 18-CDIP (0.300", 7.62mm)
• Number Of Channels: 1
• Number Of Elements: 1
• Power Supply Requirement: Dual
• Common Mode Rejection Ratio: 75dB
• Voltage Gain Db: 80dB
• Input Resistance: 20000@±15VMohm
• Input Offset Voltage: 0.1@±15VmV
• Input Bias Current: 6000@±15VnA
• Single Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (typ): ±5/±9/±12/±15V
• Rail/rail I/o Type: No
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): ±4.5V
• Dual Supply Voltage (max): ±18V
• Operating Temp Range: -25C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 18
• Package Type: CDIP
• Application: Used in high-precision data acquisition and instrumentation applications
• Bandwidth: 570 kHz
• Current, Input Bias: 2 nA
• Current, Input Offset: 0.5 nA
• Current, Supply: 3 mA
• Noise, Voltage (rti): 0.12 μV p-p
• Resistance, Input: 50 Kilohms
• Temperature, Operating, Maximum: 85 °C
• Temperature, Operating, Minimum: -25 °C
• Temperature, Operating, Range: -25 to +85 °C
• Voltage, Input: -10.5 to +15 V
• Voltage, Input Offset: 40 μV
• Voltage, Noise: 540 nV/sqrt Hz
• Voltage, Offset, Input: 40 μV (Typ.) @ 25 °C
• Voltage, Output Swing: ±13.8 V
• Voltage, Supply: ±4.5 to ±18 V
• Low Offset Voltage: 50 mV Max
• Very Low Offset Voltage Drift: 0.3 mV⁄8C Max
• Excellent Output Drive: 610 V at 650 mA
• Capacitive Load Stability: to 1 mF
• Gain Range: 0.1 to 10,000
• Excellent Linearity: 16-Bit at G == 1000
• No. Of Amplifiers: 1
• Amplifier Output: Differential
• Cmrr: 125dB
• Supply Voltage Range: ± 4.5V To ± 18V
• Supply Current: 3.4mA
• Rohs Compliant: No
• Output Type: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: Not Compliant

AMP01
Gain accuracy is determined by the ratio accuracy of R
combined with the gain equation error of the AMP01 (0.6%
max for A/E grades).
All instrumentation amplifiers require attention to layout so
thermocouple effects are minimized. Thermocouples formed
between copper and dissimilar metals can easily destroy the
TCV
0.15 V/ C. Resistors themselves can generate thermoelectric
EMF’s when mounted parallel to a thermal gradient. “Vishay”
resistors are recommended because a maximum value for ther-
moelectric generation is specified. However, where thermal
gradients are low and gain TCs of 20 ppm–50 ppm are suffi-
cient, general-purpose metal-film resistors can be used for R
and R
COMMON-MODE REJECTION
Ideally, an instrumentation amplifier responds only to the dif-
ference between the two input signals and rejects common-
mode voltages and noise. In practice, there is a small change in
output voltage when both inputs experience the same common-
mode voltage change; the ratio of these voltages is called the
common-mode gain. Common-mode rejection (CMR) is the
logarithm of the ratio of differential-mode gain to common-
mode gain, expressed in dB. CMR specifications are normally
measured with a full-range input voltage change and a specified
source resistance unbalance.
The current-feedback design used in the AMP01 inherently
yields high common-mode rejection. Unlike resistive feedback
designs, typified by the three-op-amp IA, the CMR is not de-
graded by small resistances in series with the reference input. A
slight, but trimmable, output offset voltage change results from
resistance in series with the reference input.
The common-mode input voltage range, CMVR, for linear
operation may be calculated from the formula:
OS
S
.
100k
10k
100
performance of the AMP01 which is typically
1M
1k
1
Figure 30. R
CMVR =
10
VOLTAGE GAIN
G
IVR –
and R
100
| V
S
R
R
2 G
S
G
Selection
OUT
|
1k
V
S
=
15V
S
10k
and R
G
(4)
G
–12–
IVR is the data sheet specification for input voltage range; V
is the maximum output signal; G is the chosen voltage gain. For
example, at +25 C, IVR is specified as 10.5 volt minimum
with 15 volt supplies. Using a 10 volt maximum swing out-
put and substituting the figures in (4) simplifies the formula to:
For all gains greater than or equal to 10, CMVR is 10 volt
minimum; at gains below 10, CMVR is reduced.
ACTIVE GUARD DRIVE
Rejection of common-mode noise and line pick-up can be im-
proved by using shielded cable between the signal source and
the IA. Shielding reduces pick-up, but increases input capaci-
tance, which in turn degrades the settling-time for signal
changes. Further, any imbalance in the source resistance be-
tween the inverting and noninverting inputs, when capacitively
loaded, converts the common-mode voltage into a differential
voltage. This effect reduces the benefits of shielding. AC
common-mode rejection is improved by “bootstrapping” the
input cable capacitance to the input signal, a technique called
“guard driving.” This technique effectively reduces the input
capacitance. A single guard-driving signal is adequate at gains
above 100 and should be the average value of the two inputs.
The value of external gain resistor R
tors R
drive the buffer amplifier (Figure 31).
GROUNDING
The majority of instruments and data acquisition systems have
separate grounds for analog and digital signals. Analog ground
may also be divided into two or more grounds which will be tied
together at one point, usually the analog power-supply ground.
In addition, the digital and analog grounds may be joined, nor-
mally at the analog ground pin on the A-to-D converter. Fol-
lowing this basic grounding practice is essential for good circuit
performance (Figure 32).
Mixing grounds causes interactions between digital circuits and
the analog signals. Since the ground returns have finite resis-
tance and inductance, hundreds of millivolts can be developed
between the system ground and the data acquisition compo-
nents. Using separate ground returns minimizes the current flow
in the sensitive analog return path to the system ground point.
Consequently, noisy ground currents from logic gates do not
interact with the analog signals.
Inevitably, two or more circuits will be joined together with their
grounds at differential potentials. In these situations, the differ-
ential input of an instrumentation amplifier, with its high CMR,
can accurately transfer analog information from one circuit to
another.
SENSE AND REFERENCE TERMINALS
The sense terminal completes the feedback path for the instru-
mentation amplifier output stage and is normally connected
directly to the output. The output signal is specified with re-
spect to the reference terminal, which is normally connected to
analog ground.
G1
and R
CMVR =
G2
; the center tap provides the required signal to
10.5 –
G
5
G
is split between two resis-
REV. D
OUT
(5)