SSM2018P Analog Devices Inc, SSM2018P Datasheet
SSM2018P
Specifications of SSM2018P
Available stocks
Related parts for SSM2018P
SSM2018P Summary of contents
Page 1
FEATURES 117 dB Dynamic Range 0.006% Typical THD kHz, Unity Gain) 140 dB Gain Range No External Trimming Required Differential Inputs Complementary Gain Outputs Buffered Control Port I–V Converter On-Chip Low External Parts Count Low Cost GENERAL ...
Page 2
SSM2018T–SPECIFICATIONS ELECTRICAL SPECIFICATIONS circuit with 18 k resistors, –V floating, and Class AB gain core bias (R IN specifications apply C.) A Parameter AUDIO PERFORMANCE Noise Headroom Total Harmonic Distortion plus Noise INPUT AMPLIFIER Bias Current ...
Page 3
ABSOLUTE MAXIMUM RATINGS Supply Voltage Dual Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
SSM2018T–Typical Performance Characteristics 0 + 15V 18k +20dB 0.010 AV = –20dB AV = 0dB 0.001 20 100 1k FREQUENCY – Hz TPC 1. SSM2018T THD + N ...
Page 5
15V S 400 300 200 100 0 10 100 1k FREQUENCY – Hz TPC 7. SSM2018T Noise Density vs. Frequency (Unity Gain, Referred to Input +25 C ...
Page 6
SSM2018T –20 –40 –60 –80 100 1k 10k 100k FREQUENCY – Hz TPC 13. SSM2018T Gain vs. Frequency 0.06 0. 10dBu IN 0. –20dB V AND V = –10dBu IN 0.03 A ...
Page 7
V = 15V S –25 –30 –35 –40 –40 – TEMPERATURE – °C TPC 19. SSM2018T Gain Constant vs. Temperature – + 15V S –29 –30 –31 –32 –33 –80 ...
Page 8
SSM2018T APPLICATIONS The SSM2018T is a trimless Voltage Controlled Amplifier (VCA) for volume control in audio systems. The SSM2018T is identi- cal to the original SSM2018 in functionality and pinout; how- ever the first professional quality audio VCA ...
Page 9
COMP 2 COMPENSATION –IN +IN V– shown later in the data sheet. Thus, for the Basic VCA circuit or the OVCE circuit, COMP3 should be left open. A compensation capacitor does need to be added between COMP1 and COMP2. Because ...
Page 10
SSM2018T Proper Operating Mode for the SSM2018T The SSM2018T has the flexibility of operating in either Class A or Class AB. This is accomplished by adjusting the amount of current flowing in the gain core (I in Figure 2). The ...
Page 11
As explained above, the gain constant has a –3500 ppm/∞C that is due to its reciprocal dependence on absolute temperature. This will cause the gain to vary over the temperature range from –40∞C to +85∞C when the ...
Page 12
SSM2018T If a symmetry trim performed, it should precede the control feedthrough trim and be done as follows: 1. Apply a 1 kHz sine wave of 10 dBu to the input with the control voltage set for ...
Page 13
Plastic DIP (N-16) Package 16 9 0.280 (7.11) PIN 1 0.240 (6.10 0.840 (21.33) 0.745 (18.93) 0.060 (1.52) 0.210 0.015 (0.38) (5.33) MAX 0.160 (4.06) 0.115 (2.93) SEATING 0.070 (1.77) 0.022 (0.558) 0.100 (2.54) PLANE 0.045 (1.15) ...
Page 14
–14– ...
Page 15
–15– ...
Page 16
–16– ...