PMR50HZPFU5L00 Rohm Semiconductor, PMR50HZPFU5L00 Datasheet - Page 3

• Manufacturer Part Number: PMR50HZPFU5L00
• Description: RES .005 OHM 1W 1% 2010 SMD
• Manufacturer: Rohm Semiconductor
• Series: PMR50r

Specifications of PMR50HZPFU5L00

• Resistance (ohms): 0.005
• Power (watts): 1W
• Composition: Thick Film
• Features: Current Sense
• Temperature Coefficient: ±100ppm/°C
• Tolerance: ±1%
• Size / Dimension: 0.197" L x 0.098" W (5.00mm x 2.50mm)
• Height: 0.020" (0.51mm)
• Lead Style: Surface Mount (SMD - SMT)
• Package / Case: 2010 (5025 Metric)
• Resistance In Ohms: 0.005
• Case: 2010 (5025 metric)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PMR50HZPFU5L00; RHM.005ASTR

TSZ22111･05･002
● Precaution for Mounting/Circuit board design
● Precautions Regarding Application Examples and External Circuits
● Precaution for Electrostatic
● Precaution for strage/Transportation
3)The component temperature could exceed 155℃(maximum operation temperature) depending on the type
3) In the ultra-low resistance value range, the parasitic inductance of the chip and the wiring pattern may
1) When a highly active halogenous (chlorine, bromine, etc.)flux is used, the remainder of flux may
2)In principle, the reflow soldering method must be used; if flow soldering method is preferred,please
4) In the ultra-low resistance value range, the resistance value after soldering may change depending on the size
5) Pay attention to the soldering condition in order to avoid problems due to silver absorption into solder.
6) Be careful when pick up the products with tweezers.
7) Soldering tip shall not touch the product when install product manually.
1) If change is made to the constant of an external circuit, allow a sufficient margin due to variations of the
2) The application examples, their constants, and other types of information contained herein are applicable
1)Product performance and soldered connections may deteriorate if the products are stored in the following
of mounting board material, the wiring pattern, heat dissipation from the surrounding components and ambient
temperature, not necessarily relevant to the loaded power. Make sure in advance you use it in the condition that
it does not damage the mounting board and the surrounding components.
influence current detection under high frequency usage. Make sure the effect before you use it.
negatively affect product performance and reliability.
Consult with the company in advance.
of pad pattern, the wiring pattern or solder amount. Make sure the effect of the change of the resistance value
before you use it.
There may be a case that the overcoat and /or the body can be chipped.
characteristics of the products and external components, including transient characteristics, as well as
static characteristics.
only when the products are used in accordance with standard methods. Therefore, if mass production is
intended, sufficient consideration to external conditions must be made.
This product is Electrostatic sensitive product, which may be damaged due to Electrostatic discharge.
Please take proper caution during manufacturing and string so that voltage exceeding Product maximum
rating won’t be applied to products. Please take special care under dry condition(e.g. Grounding of human
body /equipment /solder iron, isolation from charged objects, setting of Ionizer, friction prevention and
temperature /humidity control).
2) Even under ROHM recommended storage condition, solderability of products over 1 year old
3) Store / transport cartons in the correct direction, which is indicated on a carton as a symbol.
places:
[a] Where the products are exposed to sea winds or corrosive gases, including Cl
[b] Where the temperature or humidity exceeds those recommended by the Company
[c] Storage in direct sunshine or condensation
[d] Storage in high Electrostatic
(Put condition for each product)may be degraded.
It is strongly recommended storage time period.
･Recommended storage condition：Temperature 5―40℃, Humidity 30―80%(Put condition for
individual product)
Otherwise bent leads may occur due to excessive stress applied when dropping of a carton..
Temperature:5―40℃, Humidity 30―80% (Put condition for individual product)
and NO
2
PRODUCTS
ULTRA LOW OHMIC RESISTORS
REV.：
< Specifications (Precautions and Prohibitions) >
００８Ｅ
TYPE
SPECIFICATION No.：ＰＭＲ５０－ＩＡ
PMR50 Series
2
, H
2
S, NH
3
, SO
2
PAGE
,
3/16