AK5358AETP AKM Semiconductor Inc, AK5358AETP Datasheet
AK5358AETP
Specifications of AK5358AETP
AK5358AETP
Available stocks
Related parts for AK5358AETP
AK5358AETP Summary of contents
Page 1
The AK5358A is a stereo A/D Converter with wide sampling rate of 8kHz ∼ 96kHz and is suitable for consumer to professional audio system. The AK5358A achieves high accuracy and low cost by using Enhanced dual bit ΔΣ techniques. The ...
Page 2
Ordering Guide AK5358AET AKD5358A ■ Pin Layout AINR AINL CKS1 VCOM AGND VA VD DGND ■ Compatibility with AK5357, AK5359 and AK5381 fs 4kHz to 96kHz S/(N+D) DR VIH@TTL Level Mode VA (Analog Supply) VD (Digital Supply) HPF Disable ...
Page 3
No. Pin Name I/O 1 AINR I 2 AINL I 3 CKS1 I 4 VCOM O 5 AGND - DGND - 9 SDTO O 10 LRCK I/O 11 MCLK I 12 SCLK I/O ...
Page 4
Note 1) Parameter Power Supplies: Analog Digital |AGND – DGND| Input Current, Any Pin Except Supplies Analog Input Voltage (AINL, AINR, CKS1 pins) Digital Input Voltage Ambient Temperature (powered applied) Storage Temperature Note 1. All voltages with respect to ...
Page 5
VA=5.0V, VD=5.0V; AGND=DGND=0V; fs=48kHz, 96kHz; SCLK=64fs; Signal Frequency=1kHz; 24bit Data; Measurement frequency=20Hz ∼ 20kHz at fs=48kHz, 40Hz ∼ 40kHz at fs=96kHz; unless otherwise specified) Parameter ADC Analog Input Characteristics: Resolution Input Voltage S/(N+D) fs=48kHz BW=20kHz fs=96kHz BW=40kHz DR (−60dBFS, ...
Page 6
VA=4.5 ∼ 5.5V; VD=2.7 ∼ 5.5V) Parameter ADC Digital Filter (Decimation LPF): Passband (Note 10) Stopband Passband Ripple Stopband Attenuation Group Delay Distortion Group Delay (Note ADC Digital Filter (HPF): 10) −3dB Frequency Response (Note (Ta=-20°C ∼ ...
Page 7
DC CHARACTERISTICS (CMOS Level Mode) (Ta=-20°C ∼ 85°C; VA=4.5 ∼ 5.5V; VD=2.7 ∼ 5.5V) Parameter High-Level Input Voltage Low-Level Input Voltage High-Level Output Voltage Low-Level Output Voltage Input Leakage Current DC CHARACTERISTICS (TTL Level Mode) (Ta=-20°C ∼ 85°C; VA=4.5 ∼ ...
Page 8
VA=4.5 ∼ 5.5V; VD=2.7 ∼ 5.5V; C Parameter Master Clock Timing 512fs, 256fs Frequency Pulse Width Low Pulse Width High 768fs, 384fs Frequency Pulse Width Low Pulse Width High LRCK Frequency Duty Cycle Slave mode Master mode ...
Page 9
Timing Diagram MCLK LRCK SCLK LRCK tSHLR SCLK tLRS SDTO MS0511-E-02 1/fCLK tCLKH tCLKL 1/fs tSCK tSCKH tSCKL Clock Timing tLRSH tSSD Audio Interface Timing (Slave mode [AK5358A] VIH VIL VIH VIL VIH VIL VIH VIL ...
Page 10
LRCK tMSLR SCLK SDTO PDN SDTO PDN MS0511-E-02 tSSD Audio Interface Timing (Master mode) tPDV tPD Power Down & Reset Timing - 10 - [AK5358A] 50%VD dSCK 50%VD 50%VD VIH VIL 50%VD VIL 2008/01 ...
Page 11
System Clock MCLK, SCLK and LRCK (fs) clocks are required in slave mode. The LRCK clock input must be synchronized with MCLK, however the phase is not critical. clock frequency. MCLK frequency, SCLK frequency and master/slave are selected by ...
Page 12
Audio Interface Format Two kinds of data formats can be chosen with the DIF pin compliment format. The SDTO is clocked out on the falling edge of SCLK. The audio interface supports both master and slave modes. In master ...
Page 13
Power down The AK5358A is placed in the power-down mode by bringing PDN pin “L” and the digital filter is also reset at the same time. This reset should always be done after power-up. In the power-down mode, the ...
Page 14
Figure 4 shows the system connection diagram. An evaluation board is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results. 10u + Rch In + Lch In 10u 2.2u + Analog 5V 10u 0.1u Digital ...
Page 15
Grounding and Power Supply Decoupling The AK5358A requires careful attention to power supply and grounding arrangements. Alternatively if VA and VD are supplied separately, the power up sequence is not critical. AGND and DGND of the AK5358A must be ...
Page 16
TSSOP (Unit: mm) *5.0 ± 0 0.22 ± 0.1 0.13 M Seating Plane NOTE: Dimension "*" does not include mold flash. ■ Material & Lead finish Package molding compound: Lead frame material: Lead frame surface treatment: MS0511-E-02 ...
Page 17
Date (YY/MM/DD) Revision 06/06/02 00 07/04/13 01 08/01/23 02 MS0511-E-02 MARKING AKM 5358AET XXYYY Pin #1 indication 1) Date Code: XXYYY (5 digits) 2) XX: Lot# YYY: Date Code Marketing Code: 5358AET 3) REVISION HISTORY Reason Page Contents First Edition ...
Page 18
These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei EMD Corporation (AKEMD) or authorized distributors as to current status ...