ALD500RA-20SEL Advanced Linear Devices Inc, ALD500RA-20SEL Datasheet - Page 9

• Manufacturer Part Number: ALD500RA-20SEL
• Description: IC ADC 17BIT 20SOIC
• Manufacturer: Advanced Linear Devices Inc

Specifications of ALD500RA-20SEL

• Number Of Bits: 17
• Power Dissipation (max): 10mW
• Voltage Supply Source: Dual ±
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Differential Inputs (V
The ALD500RAU/ALD500RA/ALD500R operates with
differential voltages within the input amplifier common-mode
voltage range. The amplifier common-mode range extends
from 1.5V below positive supply to 1.5V above negative
supply. Within this common-mode voltage range, common-
mode rejection is typically 95dB.
The integrator output also follows the common-mode voltage.
When large common-mode voltages with near full-scale
differential input voltages are applied, the input signal drives
the integrator output to near the supply rails where the
integrator output is near saturation. Under such conditions,
linearity of the converter may be adversely affected as the
integrator swing can be reduced. The integrator output must
not be allowed to saturate. Typically, the integrator output can
swing to within 0.9V of either supply rails without loss of
linearity.
Analog Ground
Analog Ground is V
Voltage Deintegration Phase. If V
ground, a common-mode voltage exists at the inputs. This
common mode signal is rejected by the high common mode
rejection ratio of the converter. In most applications, V
set at a fixed known voltage (i.e., power supply ground). All
other ground connections should be connected to digital
ground in order to minimize noise at the inputs.
Differential Reference (V
The reference voltage can be anywhere from 1V of the power
supply voltage rails of the converter. Roll-over error is caused
by the reference capacitor losing or gaining charge due to the
stray capacitance on its nodes. The difference in reference for
ALD500RAU/ALD500RA/ALD500R
EXTERNAL INPUT
POLARITY DETECTION
COMPARATOR
INTEGRATOR
OUTPUT
OUTPUT
- IN
(C
(V
OUT
INT
ANALOG INPUT
during Auto Zero Phase and Reference
+ IN
)
)
INTEGRATE
,V
+ REF
- IN)
Positive Input Signal (V
, V
-
- REF
IN is different from analog
)
Figure 4. Comparator Output
IN
Advanced Linear Devices
)
REFERENCE
DEINTEGRATE
ZERO
CROSSING
-
IN is
(+) or (-) input voltages will cause a roll-over error. This error
can be minimized by using a large reference capacitor in
comparison to the stray capacitance.
Phase Control Inputs (A, B)
The A and B logic inputs select the ALD500RAU/ALD500RA/
ALD500R operating phase. The A and B inputs are normally
driven by a microprocessor I/O port or external logic, using
CMOS logic levels. For logic control functions of A and B logic
inputs, see Table 1.
Comparator Output (C
By monitoring the comparator output during the Input Signal
Integration Phase, which is a fixed signal integrate time
period, the input signal polarity can be determined by the
microcontroller controlling the conversion. The comparator
output is HIGH for positive signals and LOW for negative
signals during the Input Signal Integration Phase. The state of
the comparator should be checked by the microcontroller at
the end of the Input Signal Integration Phase, just before
transition to the Reference Voltage Deintegration Phase. For
very low level input signals noise may cause the comparator
output state to toggle between positive and negative states.
For the ALD500RAU/ALD500RA/ALD500R, this noise has
been minimized to typically within one count.
At the start of the Reference Voltage Deintegration Phase,
comparator output is set to HIGH state. During the Reference
Voltage Deintegration Phase, the microcontroller must monitor
the comparator output to make a HIGH-to-LOW transition as
the integrator output ramp crosses zero relative to analog
ground.
complete. The microcontroller then stops and records the
pulse count. The internal comparator delay is 1 sec, typically.
The comparator output is undefined during the Auto Zero
Phase.
EXTERNAL INPUT
POLARITY DETECTION
COMPARATOR
INTEGRATOR
ANALOG INPUT
INTEGRATE
OUTPUT
OUTPUT
This transition indicates that the conversion is
(C
Negative Input Signal (V
(V
OUT
INT
)
)
OUT
)
IN
)
REFERENCE
DEINTEGRATE
ZERO
CROSSING
0V
9