IR3856MTRPBF International Rectifier, IR3856MTRPBF Datasheet - Page 4

• Manufacturer Part Number: IR3856MTRPBF
• Description: IC BUCK SYNC ADJ 6A 17PQFN
• Manufacturer: International Rectifier
• Series: SupIRBuck™r
• Type: Step-Down (Buck)r

Specifications of IR3856MTRPBF

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.7 ~ 18.9 V
• Current - Output: 6A
• Frequency - Switching: 250kHz ~ 1.5MHz
• Voltage - Input: 1.5 ~ 21 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 17-PowerVQFN
• Power - Output: 1.11W
• Primary Input Voltage: 21V
• No. Of Outputs: 1
• Output Voltage: 18.9V
• Output Current: 6A
• No. Of Pins: 17
• Operating Temperature Range: -40°C To +125°C
• Peak Reflow Compatible (260 C): Yes
• Rohs Compliant: Yes
• Leaded Process Compatible: Yes
• Part Status: Preferred
• Package: PQFN / 4 x 5
• Circuit: Single Output
• Iout (a): 6
• Switch Freq (khz): 250 - 1500
• Input Range (v): 1.5 - 21
• Output Range (v): 0.7 - 0.9*Vin
• Ocp Otp Uvlo Pre-bias Soft Start And: PGOOD + EN + SEQ + OVP + SYNC
• Design Tool: Yes
• Server Storage: Yes
• Routers Switches: Yes
• Base Station Telecom: Yes
• Digital Home Media: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Pin Description
4;17
Rev2.0
Pin
10
11
12
13
14
15
16
1
2
3
5
6
7
8
9
PGood
Enable
Name
SS/SD
OCSet
Comp
PGnd
Vsns
Sync
Boot
Gnd
Seq
V
SW
V
Fb
Rt
CC
IN
Inverting input to the error amplifier. This pin is connected directly to the
output of the regulator via resistor divider to set the output voltage and
provide feedback to the error amplifier.
Sense pin for PGood
Output of error amplifier. An external resistor and capacitor network is
typically connected from this pin to Fb pin to provide loop compensation.
Signal ground for internal reference and control circuitry.
Set the switching frequency. Connect an external resistor from this pin to
Gnd to set the switching frequency. See Table 1 for Fs vs. Rt.
Soft start / shutdown. This pin provides user programmable soft-start
function. Connect an external capacitor from this pin to Gnd to set the
start up time of the output voltage. The converter can be shutdown by
pulling this pin below 0.3V.
Current limit set point. A resistor from this pin to SW pin will set the
current limit threshold.
Power Good status pin. Output is open drain. Connect a pull up resistor
from this pin to Vcc.
Sync pin, connect external system clock to synchronize multiple POLs
with the same frequency
This pin powers the internal IC and the drivers. A minimum of 1uF high
frequency capacitor must be connected from this pin to the power ground
(PGnd).
Power Ground. This pin serves as a separated ground for the MOSFET
drivers and should be connected to the system’s power ground plane.
Switch node. This pin is connected to the output inductor.
Input voltage connection pin.
Supply voltage for high side driver. A 0.1uF capacitor must be connected
from this pin to SW.
Enable pin to turn on and off the device. Use two external resistors to set
the turn on threshold (see Enable section). Connect this pin to Vcc if it is
not used.
Sequence pin. Use two external resistors to set Simultaneous Power up
sequencing. If this pin is not used connect to Vcc.
Description
IR3856MPbF
PD-97528
4