NLB-400-T1 RFMD, NLB-400-T1 Datasheet - Page 3

• Manufacturer Part Number: NLB-400-T1
• Description: IC AMP MMIC GAAS 6GHZ 4-MICROX
• Manufacturer: RFMD

Specifications of NLB-400-T1

• Current - Supply: 47mA
• Frequency: 0Hz ~ 6GHz
• Gain: 10.8dB ~ 11.5dB @ 4GHz ~ 6GHz
• Noise Figure: 4.1dB @ 3GHz
• P1db: 14.6 @ 6GHz
• Package / Case: 4-Micro-X
• Rf Type: LMDS, VSAT, WLAN, UNII, DWDM, PTP PMP
• Voltage - Supply: 3.6V ~ 4.2V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Test Frequency: -
• Other names: 689-1005-2; NLB-400TR7

Rev A10 DS070123
Pin
1
2
3
4
Function
RF OUT
RF IN
GND
GND
Seating Plane
Description
RF input pin. This pin is NOT internally DC blocked. A DC blocking capacitor,
suitable for the frequency of operation, should be used in most applica-
tions. DC coupling of the input is not allowed, because this will override the
internal feedback loop and cause temperature instability.
Ground connection. For best performance, keep traces physically short
and connect immediately to ground plane.
RF output and bias pin. Biasing is accomplished with an external series
resistor and choke inductor to V
current into this pin to a desired level. The resistor value is determined by
the following equation:
Care should also be taken in the resistor selection to ensure that the cur-
rent into the part never exceeds maximum datasheet operating current
over the planned operating temperature. This means that a resistor
between the supply and this pin is always required, even if a supply near
5.0V is available, to provide DC feedback to prevent thermal runaway.
Because DC is present on this pin, a DC blocking capacitor, suitable for the
frequency of operation, should be used in most applications. The supply
side of the bias network should also be well bypassed.
Same as pin 2.
0.08 S
R
6
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical
support, contact RFMD at ([phone] or [e-mail].
=
S
D
(
------------------------------------------ -
V
A
CC
1 J
L 3
B
–
C
I
V
CC
N 5
E
DEVICE
F
Package Drawing
2
)
K x 3
G
CC
4 M
. The resistor is selected to set the DC
H
0.1
Gauge Plane
1
2
3
4
5
NOTE: All dimensions are in millimeters, and
the dimensions in inches are for reference only.
A
B
C
D
G
H
K
M
N
E
F
J
L
0.436 0.510 0.586 0.017 0.020 0.023
0.535 0.660 0.785 0.021 0.026 0.031
Min.
2.39
2.19
1.91
1.32
0.10
0.05
0.65
0.85
4.53
4.73
MILLIMETERS
0.535 REF.
Nom. Max.
2.54
2.34
2.16
1.52
0.15
0.10
0.75
0.95
4.68
4.88
2.69
2.49
2.41
1.72
0.20
0.15
0.85
1.05
4.83
5.03
0.094 0.100 0.106
0.086 0.092 0.098
0.075 0.085 0.095
0.052 0.060 0.068
0.004 0.006 0.008
0.002 0.004 0.006
0.025 0.029 0.033
0.033 0.037 0.041
0.178 0.184 0.190
0.186 0.192 0.198
Min.
0.021 REF.
INCHES
Nom. Max.
RF IN
Interface Schematic
NLB-400
RF OUT
3-25
3