MICRF213AYQS Micrel Inc, MICRF213AYQS Datasheet - Page 2

• Manufacturer Part Number: MICRF213AYQS
• Description: IC RX 3.3V 300-350 MHZ 16-QSOP
• Manufacturer: Micrel Inc

Specifications of MICRF213AYQS

• Operating Temperature: -40°C ~ 105°C
• Frequency: 300MHz ~ 350MHz
• Sensitivity: -110dBm
• Data Rate - Maximum: 7.2 kbps
• Modulation Or Protocol: AM, OOK
• Applications: ISM, Garage Door Openers, RKE
• Current - Receiving: 3.9mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 3 V ~ 3.6 V
• Package / Case: 16-QSOP
• Receiving Current: 3.9mA
• Data Rate: 7.2Kbps
• Modulation Type: ASK, OOK
• Frequency Range: 300MHz To 350MHz
• Rf Ic Case Style: QSOP
• No. Of Pins: 16
• Supply Voltage Range: 3V To 3.6V
• Sensitivity Dbm: -110dBm
• Rohs Compliant: Yes
• Operating Temperature (min): -40C
• Operating Temperature (max): 105C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 576-1649-5

Pin Configuration
Pin Description
16-Pin
QSOP
Micrel, Inc.
May 2007
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
GNDRF
GNDRF
SHDN
CAGC
Name
SEL0
SEL1
RSSI
GND
RO1
ANT
VDD
CTH
RO2
Pin
DO
SQ
NC
Pin Function
Reference resonator input connection to Colpitts oscillator stage. May also be driven by external reference
signal of 1.5V p-p amplitude maximum.
Negative supply connection associated with ANT RF input.
RF signal input from antenna. Internally AC-coupled. It is recommended that a matching network with an
inductor-to-RF ground is used to improve ESD protection.
Negative supply connection associated with ANT RF input.
Positive supply connection for all chip functions.
Squelch control logic input with an active internal pull-up when not shut down.
Logic control input with active internal pull-up. Used in conjunction with SEL1 to control the demodulator low
pass filter bandwidth. (See filter table for SEL0 and SEL1 in application section)
Shutdown logic control input. Active internal pull-up.
Logic control input with active internal pull-up. Used in conjunction with SEL0 to control the demodulator low
pass filter bandwidth. (See filter table for SEL0 and SEL1 in application subsection)
Demodulation threshold voltage integration capacitor connection. Tie an external capacitor across CTH pin
and GND to set the settling time for the demodulation data slicing level. Values above 1nF are
recommended and should be optimized for data rate and data profile.
AGC filter capacitor connection. CAGC capacitor, normally greater than 0.47uF, is connected from this pin to
GND
Received signal strength indication output. Output is from a buffer with 200 ohms typical output impedance.
Reference resonator input connection to Colpitts oscillator stage, 7pF, in parallel with low resistance MOS
switch-to-GND, during normal operation. Driven by startup excitation circuit during the internal startup control
sequence.
Negative supply connection for all chip functions except RF input.
Demodulated data output.
Not Connected (Connect to Ground)
GNDRF
GNDRF
SHDN
SEL0
VDD
RO1
ANT
SQ
1
2
3
4
5
6
7
8
MICRF213AYQS
2
16 RO2
15
14
13
12
11
10
9
NC
RSSI
CAGC
CTH
SEL1
DO
GND
M9999-052307-A
[phone]
MICRF213