ZM3102AE-CME1 Sigma Designs Inc, ZM3102AE-CME1 Datasheet - Page 7

• Manufacturer Part Number: ZM3102AE-CME1
• Description: MOD Z-WAVE PCB ASSY EU ZM3102N
• Manufacturer: Sigma Designs Inc
• Series: Z-WAVEr

Specifications of ZM3102AE-CME1

• Frequency: 868MHz
• Data Rate - Maximum: 40kbps
• Modulation Or Protocol: FSK
• Applications: AV Control, Home Automation, Sensor Networks
• Power - Output: -22dBm ~ -2dBm
• Sensitivity: -98dBm
• Voltage - Supply: 2.1 V ~ 3.6 V
• Current - Receiving: 23mA
• Current - Transmitting: 36mA @ 0dBm
• Data Interface: PCB, Surface Mount
• Memory Size: 32kByte Flash, 2kByte SRAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -15°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 370100770; 703-1024

Zensys A/S
DSH10756-6
All signals in Table 1 except RF, VCC and GND are connected directly to the corresponding signals on
the ZW0301 Z-Wave Single Chip on the ZM3102N Z-Wave Module. A detailed description of these
signals is given in the ZW0301 Z-Wave Single Chip datasheet [1].
Name
ADC[3:0]
GND
INT[1:0]
P[0.1-0.0],
P[1.7-1.0]
MISO
MOSI
PWM
RESET_N
RF
RXD
SCK
TRIAC
TXD
VCC
ZEROX
1.
1
1
1
Please note that the SPI interface (MISO, MOSI and SCK) is not available for the Application SW in some Z-Wave
protocol API’s, see [3]
Notch #
1, 6, 12,
10, 13,
3, 4, 5,
7, 8, 9,
10, 13,
14, 15
16, 17
14, 15
3, 4
18
10
13
15
11
14
7
9
4
2
8
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
Table 1 ZM3102N Signal Description
ZM3102N Z-Wave Module Datasheet
Description
Analog-to-Digital Converter input. The ADC is 12/8 bit and can
use either VCC or an internal/external voltage as reference.
ADC3: input
ADC2: input
ADC1: input / lower reference
ADC0: input / higher reference
Ground signal
Interrupt: The signal can be either level or edge trigged. When in
power down mode, the ZM3102N Z-Wave Module’s MCU can be
woken up by asserting the interrupt signal INT1.
In/Out: General purpose I/O signal.
Master-In-Slave-Out SPI interface: output in slave mode
operation and input in master mode operation.
Master Out Slave In SPI interface: input in slave mode operation
and output in master mode operation.
Pulse Width Modulator Output: Used for frequency variation
applications.
Reset: Active low reset. The ZW0301 Single Chip has an
integrated Power-On-Reset and Brown-out detection circuitry.
RF Input/Output
UART Receive Data: Supports 9.6kbaud, 38.4kbaud,
115.2kbaud.
SPI Clock: Can be used as either master SPI clock output or
slave SPI clock input.
TRIAC Control: A triac controller is implemented in the ZW0301
Single Chip that can controls a triac on the Application Module
like light dimmer modules etc.
UART Transmit Data: Supports 9.6kbaud, 38.4kbaud,
115.2kbaud.
ZM3102N supply voltage.
Zero Cross Detection: Zero cross detection signal used on
dimmer modules detecting 120/240V zero crossing.
Product Description
Page 4 of 14
2007-10-01