CC-WMX-LB69-EA Digi International, CC-WMX-LB69-EA Datasheet - Page 22

• Manufacturer Part Number: CC-WMX-LB69-EA
• Description: CONNECTCORE WI-MX51 MODULE
• Manufacturer: Digi International

Specifications of CC-WMX-LB69-EA

• Frequency: 2.4GHz, 4.9GHz ~ 5.85GHz
• Data Rate - Maximum: 65Mbps
• Modulation Or Protocol: BPSK, CCK, DBPSK, DQPSK, QPSK, 16-QAM, 64-QAM
• Applications: General Purpose
• Power - Output: 17dBm
• Antenna Connector: U.FL x 2
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Operating Temperature: -
• Sensitivity: -
• Memory Size: -
• Data Interface: -
• Current - Transmitting: -
• Current - Receiving: -
• Other names: 602-2321; CC-W51-LB6A-EA; CC-W51-LB6A-VE; CC-WMX-LB6A-EA

© 2010 Digi International, Inc.
ConnectCore Wi‐i.MX51
Jumper
J3
J4
J5
J6
J9
J13
J14
J16
J17
J20
J24
J28
J29
J30
J31
Name
COINCELL BATT
JTAG MODE
VLIO DC/DC
VLIO BATT
USER LED 2
+5 ENABLE
USB OTG VBUS
USER LED 1
WLAN DISABLE
TOUCH SELECT
LCD 1
TOUCH SELECT
LCD 2
USER BUTTON 1
USER BUTTON 2
XBEE DOUT
XBEE CTS#
Description
Supplies the real time clock with 3V backup power
from the coincell battery
Select between boundary scan and debug mode
This jumper allows disconnecting VLIO coming
from the 9-30V DC/DC converter
This jumper allows disconnecting VLIO coming
from the external Lithium battery connector (J23)
User LED2 enable/disable
This jumper allows to enable/disable the +5V DC/
DC converter (U2)
Connect/disconnect the external charge pump
controller on USB OTG VBUS pin
User LED1 enable/disable
Disable the WLAN interface on the module (if
present). On ConnectCore Wi-i.MX51 this signal is
not used. It is a legacy signal.
This jumper allows to select if the touch interface
used on LCD1 is coming from the module touch
controller - or is generated by a touch controller
located on the LCD board.
This jumper allows to select if the touch interface
used on LCD2 is coming from the module touch
controller - or is generated by a touch controller
located on the LCD board.
UserBUTTON1 enable/disable
UserBUTTON2 enable/disable
Connect/disconnect the XBEE DOUT signal from
the ConnectCore module. This is required when
using UART3/TTL header.
Connect/disconnect the XBEE CTS# signal from the
ConnectCore module. This is required when using
UART3/TTL header.
Settings
Closed = battery backup enabled (DEAFULT)
Open = battery backup disabled
Closed = boundary scan
Open = ARM debug (DEFAULT)
Closed = VLIO from 9-30V DC/DC connected
(DEFAULT)
Open = VLIO from 9-30V DC/DC disconnected
Closed = VLIO from battery connector J23
connected (DEFAULT)
Open = VLIO from battery connector J23
disconnected
Closed = USER LED2 enabled (DEFAULT)
Open = USER LED2 disabled
Closed = +5V DC/DC converter enabled
(DEFAULT)
Open = +5V DC/DC converter disabled
Closed = charge-pump connected to USB OTG
VBUS (DEFAULT)
Open = charge-pump disconnected from USB OTG
VBUS
Closed = USER LED1 enabled (DEFAULT)
Open = USER LED1 disabled
Closed = WLAN disabled
Open = WLAN enabled (DEFAULT)
Closed = TOUCH on LCD board
Open = TOUCH from ConnectCore module
(DEFAULT)
Closed = TOUCH on LCD board
Open = TOUCH from ConnectCore module
(DEFAULT)
Closed = USER BUTTON1 enabled (DEFAULT)
Open = USER BUTTON1 disabled
Closed = USER BUTTON2 enabled (DEFAULT)
Open = USER BUTTON2 disabled
Closed = XBEE DOUT connected
Open = XBEE DOUT disconnected (DEFAULT)
Closed = XBEE CTS# connected
Open = XBEE CTS# disconnected (DEFAULT)
22