E8MS-01 Omron, E8MS-01 Datasheet - Page 13

• Manufacturer Part Number: E8MS-01
• Description: SENSOR PRESSURE POSITIV 0-100KPA
• Manufacturer: Omron
• Series: E8MSr

Specifications of E8MS-01

• Pressure Type: Gauge
• Operating Pressure: 14.50 PSI, 100 kPa
• Port Size: Male, 1/8" (3.175mm) 27 NPT
• Output: Digital
• Voltage - Supply: 12 V ~ 24 V
• Termination Style: Cable
• Operating Temperature: 0°C ~ 50°C
• Package / Case: Module
• Mounting Style: Desktop
• Maximum Operating Temperature: + 50 C
• Minimum Operating Temperature: 0 C
• Operating Supply Voltage: 12 V
• Output Voltage: 1 V to 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: E8MS01

● Installation
Connector Assembly Procedure
1. Processing the Sensor I/O Connector Cable End
(1)The cable end is semi-stripped.
(2)Cut the ends as shown in the
2. Connecting the Sensor Cable and Connector
Wire Preparation
Strip 7 to 8 mm of the wire
insulation as shown by the strip
gauge on the side of the connector
and twist stranded wires several
times.
Connection Procedure
(1)Use a flat-blade
(2)Insert the wire all the way into the wire insert hole. Make sure that
• Terminal numbers are engraved on the Sensor Connector. Refer to
Terminal No.
the following chart and be sure that the terminal numbers
correspond to the wire colors and insert the wires all the way in.
illustration on the right, and do
not peel the shield.
screwdriver to press in
the operating lever in
the operating hole until
the lever locks.
the insulated part of the wire is in the wire insert hole and that the
end of the wire passes through the wire connection section.
Wire connection
section
1
2
3
4
Model
E89-M4-S
--------
Insulated part
of the wire
Black (IN: 1 to 5 V)
Semi-stripped
Brown (Vcc)
Blue (GND)
I/O code
Pink (LED lighting input)
Operating hole
20 mm min.
7 to 8 mm
30
Flat-blade screwdriver
E89-M3-S
Wire insert hole
50
10
(3)Insert a flat-blade screwdriver
Connection Release Procedure
(1)Press in the operating lever, check that
(2) Be sure to release the operating lever
● Others
(1)Do not use the Sensor in an environment subject to corrosive or
(2)Do not use the Sensor alongside a high-tension voltage line or
(3)Do not expose the Sensor to water.
(4)Be sure to use the Sensor under the rated pressure.
(5)Do not insert any wire into the pressure port. Doing so may
(6)Do not apply any tensile strength in excess of 20N for E8MS, 30N
(7)Compressor oil and air-borne water may form droplets at the
(8)Do not pull the cables. When removing the connectors for external
into the release hole and
lightly pull back the lever.
The lever will be released
when a click is heard.
it is locked, and then pull out the wire.
combustible gases.
power line.
damage the pressure elements and cause a malfunction.
for E8M to the cables or connectors.
pressure receiving section of the Sensor. Remove the oil and water
using an air filter to prevent damage to Sensor elements.
connection, be sure to use the lock lever.
after releasing the wire. If, however,
wiring will be performed after
releasing the connection, perform the
wiring without releasing the operating
lever.
(3)Last, check the following points.
•The operating lever is released.
•Check step 2 again.
(Lightly pull on the wires. If there is
resistance, the wires are connected.)
Operating lever
(White)
E8MS/E8M
Operating lever
(White)
Release hole
13