73S8009C-32IM/F Maxim Integrated Products, 73S8009C-32IM/F Datasheet - Page 20

• Manufacturer Part Number: 73S8009C-32IM/F
• Description: IC PWR MGMT/SMART CARD INT 32QFN
• Manufacturer: Maxim Integrated Products

Specifications of 73S8009C-32IM/F

• Applications: Smart Card Reader, Writer
• Voltage - Supply: 3 V ~ 3.6 V
• Package / Case: 32-VFQFN Exposed Pad
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Interface: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

73S8009C Data Sheet
3.4
Four separate digital inputs and two outputs allow direct control of the card interface from the host:





Interrupt output to the host: When the card is not activated, the OFF pin informs the host about the card
presence only (Low = No card in the reader, high = card inserted). When CMDVCC (#/% signals) is/are
set low (card activation sequence requested from the host), low level on OFF means a fault has been
detected (e.g. card removal during card session, or voltage fault, or thermal / over-current fault) that
automatically initiates a deactivation sequence. The smart card pass through signals are enabled when
the RDY conditions are met.
3.5
The 73S8009C smart card interface IC incorporates an LDO voltage regulator for the card power supply,
V
sequence of CMDVCC# and CMDVCC%. This regulator is able to provide 1.8V, 3V or 5V card voltage
sourced from the V
(except for the ON/OFF circuitry which is powered from V
upon fault detected by an overcurrent condition or card removal event. The voltage regulator can provide
a card current of 65 mA in compliance with EMV 4.1 for 3-V and 5-V cards and 40 mA for 1.8 V cards.
The signals CMDVCC# and CMDVCC% control the turn-on, output voltage value, and turn-off of V
When either signal is asserted low, V
(within 400ns of each other), V
asserted low (to command V
CMDVCC# is asserted low, it will be ignored (and vice versa.)
At the assertion (low) of either or both CMDVCC (#/% signals), V
V
high. Approximately 510 µs after the fall of CMDVCC (#/%), the circuit will check the see if V
above the required minimum value (indicated by RDY=1) and if not, will begin an emergency deactivation
sequence. During the 510 µs time, card removal, or de-assertion of CMDVCC (#/%) shall also initiate an
emergency deactivation sequence. The circuit provides over-current protection and limits Icc to 150 mA,
maximum for self-protection. When an over-current condition is sensed, the circuit will invoke a
de-activation sequence.
20
CC
CC
Pin CS: Chip select control.
Pin CMDVCC# and/or CMDVCC%: When low, starts an activation sequence.
Pin RSTIN: controls the card RST signal.
Pin RDY: Indicates when smart card power supply is stable and ready.
Pin OFF: Indicator of card presence and any card fault conditions.
(V
rises to an acceptable value, and stays above that value for approximately 20 µs, RDY will be set
P
System Controller Interface
Card Power Supply and Voltage Supervision
to V
CC
conversion uses an internal LDO). The voltage output is controlled by the digital input
P
power supply. Internal digital circuitry is also powered by the V
CC
CC
to be 5 V) and at a much later time (greater than 2 µs, typically),
will ramp to 1.8 V. These signals are edge triggered. If CMDVCC% is
CC
will ramp to the selected value or if both signals are asserted low
PC
). A card deactivation sequence is forced
CC
will rise to the requested value. When
P
power supply
DS_8009C_025
CC
is at or
CC
Rev. 1.5
.