LS027B7DH01 Sharp Microelectronics, LS027B7DH01 Datasheet
LS027B7DH01
Specifications of LS027B7DH01
Available stocks
Related parts for LS027B7DH01
LS027B7DH01 Summary of contents
Page 1
... Technical Document LCD Specification LCD Group LS027B7DH01 LCD Module Preliminary Product Specification April 2009 WQVGA Monochrome HR-TFT Transflective Memory LCD featuring FPC connector, 17.5% reflectivity with 14:1 contrast. ...
Page 2
... Technical Literature TFT-LCD Module Model No. LS027B7DH01 The technical Literature is subject to change without any prior notice for the purpose of product improvement. Please contact Sharp or its representative before designing your product based on this literature. Liquid Crystal Display Group SHARP CORPORATION No. Date For Notice ...
Page 3
DATE PARAGRAPH DRAWING No. 5th April 2010 RECORDS OF REVISION REF.PAGE REVISED No. A SUMMARY First issue ...
Page 4
... Contact and consult with a SHARP sales representative for any questions about this device. SPEC No. LCY-1210401A NOTICE ・Office automation ・Telecommunication equipment ・Industrial control ・Consumer electronics ・Nuclear power control equipment MODEL No. PAGE LS027B7DH01 1 ...
Page 5
... As this LCD module is composed electronic circuits sensitive to electrostatic discharge of 200V or more. Handle with care using cautions for the followings: Operators Operators must wear anti-static wears to prevent electrostatic charge up to and discharge from human body. SPEC No. MODEL No. LCY-1210401A [For handling and system design] PAGE LS027B7DH01 2 ...
Page 6
... Containers and styroform used in transporation and storage may charge electrostatic (from friction and peeling) or electrostatic charge from human body, etc. may cause containers and styroform to have induced charge. Proper electrostatic measure should be taken for containers and storage material. SPEC No. MODEL No. LCY-1210401A LS027B7DH01 PAGE 3 ...
Page 7
... Store the LCD panel around room temperature as much as possible. Also, storing the LCD panel in high humidity will damage the polarizer. Store in normal room temperature as much as possible. (3) Keeping Method a．No direct sun light SPEC No. MODEL No. LCY-1210401A [For operating LCD module] [Precautions for Storage] b．Store in trays and in dark room PAGE LS027B7DH01 4 ...
Page 8
... FPC : (1) FPC bend R should be 0.45mm or greater and R should be even. In LCD panel an connective area, do not bend FPC into polarizer film side. (2) Do not hang LCD module by FPC or apply force to FPC. SPEC No. MODEL No. LCY-1210401A [Other Notice] Discarding liquid crystal modules PAGE LS027B7DH01 5 ...
Page 9
... Specification.................................................................................................................................7 4．Input Terminal names and function................................................................................................................8 5．Absolute Maximum Rating ..............................................................................................................................9 6．Electrical Characteristics...............................................................................................................................10 7．Optical Characteristics ..................................................................................................................................21 8．Outline Dimension..........................................................................................................................................23 9．External Circuit Example ...............................................................................................................................24 10． External Power Supply Circuit ..................................................................................................................25 11．Packaging......................................................................................................................................................26 12. Reliability Test Conditions...........................................................................................................................28 SPEC No. MODEL No. LCY-1210401A LS027B7DH01 Index PAGE 6 ...
Page 10
... Weight Surface Hardness (Remark) Refer to Figure 8-1 for detailed dimension and tolerance. SPEC No. MODEL No. LCY-1210401A LS027B7DH01 Specification 6.86cm (2.7”) 58.8 (H) × 35.28 (V） 400 （H） × 240 （V） 0.147 (H） × 0.147 (V） Stripe arrangement 62.8 (W) × ...
Page 11
... Chip select signal External COM inversion signal input (H: Active) Display ON/OFF signal Analalog power supply Digital power supply COM inversion mode switch terminal Logic GND Analog GND External COM signal input EXTMODE=”H” PAGE LS027B7DH01 Remark 【Remark 4-2】 【Remark 4-1】 8 ...
Page 12
... Condensation may cause electrical leak and the module may not meet s specification. 【Remark 5-5】Operating temperature is temperature that guarantess operation only. For contrast, response speed, and other display quty, module is evaluated at Ta=+25℃. SPEC No. MODEL No. LCY-1210401A LS027B7DH01 Code MIN. MAX. VDDA -0.3 ＋ ...
Page 13
... Input singal Lo voltage ※Can operate below VDD voltage, however, operation around 3V is recommended. 【Remark 6-1】 Also applicable to EXTMODE=”H”. 【Remark 6-2】 Applies to SCLK, SI, SCS, DISP, EXTCOMIN. SPEC No. MODEL No. LCY-1210401A LS027B7DH01 Code MIN. TYP. ＋4.8 ＋5.0 VDDA VDD ＋4.8 ＋ ...
Page 14
... Remark 2) VDD and VDDA shouldl simultaneously or VDD should fall first SPEC No. LCY-1210401A On Sequence Normal operation ③※1 ④※1 ② Normal operation Normal operation Normal operation T4: 30us or more T5 more T6 more MODEL No. LS027B7DH01 Off sequence ⑤ ⑥ ⑦ GND GND GND ※2 GND ※2 GND T3: 30us or more PAGE ...
Page 15
... MODEL No. LS027B7DH01 VDDA=＋5.0V、VDD=＋5.0V、GND=0V、Ta=25℃ MAX Unit Remark MHz 1000 VDDA=＋5.0V、VDD=＋5.0V、GND=0V、Ta=25℃ MAX Unit Remark 50 ns ...
Page 16
... EXTCOMIN signal 90% 90% EXTCOMIN 10% 10% trEXTCOMIN tfEXTCOMIN DISP signal 90% 90% DISP 10% 10% trDISP tfDISP * SCS,SI,SCLK、DISP、EXTCOMIN: 3V input voltage SPEC No. LCY-1210401A twSCSH 10% tfSI twSCLKH twSCLKL 90% 50% 50% 50% 10% fEXTCOMIN 50% 50% twEXTCOMINH MODEL No. PAGE LS027B7DH01 twSCSL 90% 50% 50% 10% thSCS tfSCS 50% 50% 13 ...
Page 17
... This is value in steady condition, not the falue of peak power at the time of COM operation. Some marging for power supply is recommended. We recommend capacitor for VDD and VDDA. (If VDD and VDDA are on separate systems, we recommend capacitor for each.) SPEC No. MODEL No. LCY-1210401A MIN TYP MAX 50 175 PAGE LS027B7DH01 Ta＝25℃ Unite Remark uW 【Remark 6-4】 uW 【Remark 6-4】 14 ...
Page 18
... When SCS becomes “L”, M0 and M2 are cleared. SPEC No. MODEL No. LCY-1210401A D397 D398 D399 D400 DUMMY DATA(don't care) Date write period Date transfer period (400ck) st latch block of binary driver on panel. st latch is being transferred (written) to pixel internal memory circuit. PAGE LS027B7DH01 thSCS (16ck) 15 twSCSL ...
Page 19
... D398 D399 D400 Date write period Date transfer period (400ck) st latch block of binary driver on panel. st latch to pixel internal memory circuit at the same time. MODEL No. LS027B7DH01 D397 D398 D399 D400 AG0 AG1 AG5 DUMMY DATA(don't care) Date transfer period (400ck) (8ck(Dummy)+8ck(address)=16ck) ...
Page 20
... Refer to 6-5-4) All Clear Mode to execute clear. DUMMY DATA: Dummy data. It can be “H” or “L” (“L” is recommended.) * M1: Frame inversion flag is enabled when EXTMODE=”L” * When SCS becomes “L”, M0 and M2 are cleared. SPEC No. MODEL No. LCY-1210401A LS027B7DH01 twSCSL thSCS M0 PAGE 17 M1 ...
Page 21
... Set it “H” DUMMY DATA: Dummy data. It can be “H” or “L” (“L” is recommended.) * M1: Frame inversion flag is enabled when EXTMODE=”L”. * When SCS becomes “L”, M0 and M2 are cleared. SPEC No. LCY-1210401A tV twSCSL thSCS MODEL No. PAGE LS027B7DH01 DUMMY DATA(don't care) 18 ...
Page 22
... COM ※ 3 ： LC inversion polarity has been set by the rising edge of EXTCOMIN. ※4：The period of EXTCOMIN should be constant. SPEC No. LCY-1210401A ※1 fCOM ※2 ※ 1 ※2 fEXTCOMIN ※ 4 MODEL No. LS027B7DH01 ※1 ※2 twEXTCOMINH ※ 1 ※ 1 fCOM ※2 twEXTCOMINH ※3 fCOM ※ 4 PAGE ...
Page 23
... L238 L L239 H L240 L SPEC No. LCY-1210401A Up Display Screen Gate Line Address Setup ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ MODEL No. LS027B7DH01 P400,L1 P400,L240 ・ ・ ・ ・ ・ ・ PAGE 20 ...
Page 24
... Measurement Equipment (LCD-5200) Optical Receiver Light Source Light Source LCD Panel MODEL No. PAGE LS027B7DH01 Ta=25℃ MAX. Unit Remark °(Degree) 【Remark 7-1】 °(Degree) °(Degree) 【Remark 7-2､3】 % 【Remark 7-3】 % 【Remark 7-5】 ...
Page 25
... Backlight luminance. The luminance can be calculated by the panel transimisivity "(0.35%)” multiply “Backlight luminance”. SPEC No. LCY-1210401A Normal Line 法線 Δθ22 Δθ11 ６時方向 6 o’clock direction Reflection intensity of white display Reflection intensity of black display Black Time Figure 7-3 Measurement of response speed MODEL No. LS027B7DH01 Δθ12 Δθ21 White PAGE 22 ...
Page 26
... Do not bend backward (toward polarizer film side) 【Remark 8-2】 Bend frequency: 3 times or less (Repeat bend condition: 180°～ 0°) <Recommended Connector> SPEC No. LCY-1210401A SMK FP12 Series: CFP-4610-0150F(Bottom side contact) Molex: 51441-1093(Bottom side contact) Figure 8-2 SMK FP12 series : CFP-4510-0150F (Top side contact) MODEL No. PAGE LS027B7DH01 23 ...
Page 27
... C3: Between VDD-VSS, B characteristics 1uF or more ceramic capacitor For actual use, please evaluate their conformity with your system and design. (Capacitor pressure resistance can be larger than resistance indicated above.) SPEC No. LCY-1210401A Figure 9-1 External Circuit (Recommended) ※Above circuit and parts are only recommendation. MODEL No. PAGE LS027B7DH01 24 ...
Page 28
... Reference circuit is shown below. SPEC No. MODEL No. LCY-1210401A Model No. S-8821 LM2750 Vin [V] min max min 2.8 5.0 4.9 2.7 5.6 4.8 S-8821 LM2750 PAGE LS027B7DH01 Note Charge pump type Charge pump type Vout Iout [A] typ max 5.0 5.1 0.04 5.0 5.2 0.04 25 ...
Page 29
... Will be indicated on serial number label as indicated in Figure 11-1 outline dimension figure. LS027B7DH01 Print Structure 0412Q00001A Serial number specification (1)Last digit of the year (2)Month and date of manufacture (3)5 digit consecutive numbers SPEC No. MODEL No. LCY-1210401A Model Number (3) (1)(2) Figure 11-1 Serial number print location PAGE LS027B7DH01 Display side Print Area 26 ...
Page 30
... TFT modules, room humidity should be made over 50%RH and take effective measure such as use of earth when opening the package. 11-3) Packaging Packaging condition is shown in Figure 11-2. SPEC No. MODEL No. LCY-1210401A Packageing size ：578mmx382mmx153mm Figure 11-2 Packaging Condition PAGE LS027B7DH01 27 ...
Page 31
... Ta=-30℃(1h)～+80℃(1h)/cycle＝5cycle （Non-operating） ±200V、200pF(0Ω) 1 time/each terminal LCD panel LCD panel center (glass cloth tape applied in load point area) φ10mm cylinder 1mm/minute Secured on stage Hold for 5 seconds after reaching test press load and then release PAGE LS027B7DH01 Remark 28 ...
Page 32
... Technical Document LCD Specification LCD Group NORTH AMERICA Sharp Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-8700 Fax: (1) 360-834-8903 www.sharpsma.com TAIWAN Sharp Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 ...