ZXLD1370EST16TC Diodes Inc, ZXLD1370EST16TC Datasheet - Page 2

• Manufacturer Part Number: ZXLD1370EST16TC
• Description: LED Drivers 6V TO 60V 11uA
• Manufacturer: Diodes Inc

Specifications of ZXLD1370EST16TC

• High Level Output Current: 18 mA
• Operating Supply Voltage: 6 V to 60 V
• Maximum Supply Current: 11 uA
• Maximum Operating Temperature: + 125 C
• Package / Case: TSSOP-16 EP
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ZXLD1370
Document number: DS32165 Rev. 4 - 2
Pin Descriptions
Notes:
STATUS
SGND
PGND
Name
GATE
FLAG
TADJ
PWM
SHP
REF
V
ADJ
ISM
N/C
N/C
Pin
V
EP
GI
AUX
IN
2. Type refers to whether or not pin is an Input, Output, Input/Output or Power supply pin.
PAD
Pin
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
(Note 2)
Type
I/O
O
O
O
O
P
P
P
P
P
I
I
-
I
I
I
Internal 1.25V reference voltage output
Connect to REF to disable thermal compensation function. (See section on thermal
Signal ground (Connect to 0V)
Power ground - Connect to 0V and pin 8 to maximize copper area
Not Connected internally – recommend connection to pin 7, (PGND), to maximize PCB
Not Connected internally – recommend connection pin 10 (GATE) to permit wide copper
Adjust input (for dc output current control)
Connect to REF to set 100% output current.
Drive with dc voltage (125mV<V
set value. The ADJ pin has an internal clamp that limits the internal node to less than
3V. This provides some failsafe should they get overdriven
Temperature Adjust input for LED thermal current control
Connect thermistor/resistor network to this pin to reduce output current above a preset
temperature threshold.
control.)
Shaping capacitor for feedback control loop
Connect 100pF ±20% capacitor from this pin to ground to provide loop compensation
Operation status output (analog output)
Pin is at 4.5V (nominal) during normal operation.
Pin switches to a lower voltage to indicate specific operation warnings or fault
conditions. (See section on STATUS output.)
Status pin voltage is low during shutdown mode
copper for thermal dissipation
trace to gate of MOSFET
Gate drive output to external NMOS transistor – connect to pin 9
Auxiliary positive supply to internal switch gate driver
Connect to V
dissipation (Refer to application section for more details)
Decouple to ground with capacitor close to device (refer to Applications section)
Input supply to device (6V to 60V)
Decouple to ground with capacitor close to device (refer to Applications section)
Current monitor input. Connect current sense resistor between this pin and V
The nominal voltage across the resistor is 225mV
Flag open drain output
Pin is high impedance during normal operation
Pin switches low to indicate a fault, or warning condition
Digital PWM output current control
Pin driven either by open Drain or push-pull 3.3V or 5V logic levels.
Drive with frequency higher than 100Hz to gate output ‘on’ and ‘off’ during dimming
control.
The device enters standby mode when PWM pin is driven with logic low level for more
than 15ms nominal (Refer to application section for more details)
Gain setting input
Used to set the device in Buck mode or Boost, Buck-boost modes
Connect to ADJ in Buck mode operation
For Boost and Buck-boost modes, connect to resistive divider from ADJ to SGND. This
defines the ratio of switch current to LED current (see application section). The GI pin
has an internal clamp that limits the internal node to less than 3V. This provides some
failsafe should they get overdriven
Exposed paddle. Connect to 0V plane for electrical and thermal management
IN
, or auxiliary supply from 6V to 15V supply to reduce internal power
www.diodes.com
2 of 36
ADJ
< 2.5V) to adjust output current from 10% to 200% of
Description
Diodes Incorporated
A Product Line of
© Diodes Incorporated
ZXLD1370
IN
March 2011