GNM1M2R61A104MA01D Murata, GNM1M2R61A104MA01D Datasheet - Page 3

• Manufacturer Part Number: GNM1M2R61A104MA01D
• Description: Capacitor Arrays & Networks 0504 0.1uF 10volts X5R 20%
• Manufacturer: Murata
• Series: GNMr

Specifications of GNM1M2R61A104MA01D

• Voltage Rating: 10 Volts
• Number Of Elements: 2
• Operating Temperature Range: - 55 C to + 85 C
• Termination Style: SMD/SMT
• Dimensions: 1.37 mm L x 1 mm W x 0.2 mm H
• Product: Ceramic Capacitor Arrays
• Capacitance: 0.1 uF
• Tolerance: 20 %
• Temperature Coefficient: X5R
• Package / Case: 0504
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

No.
15
16
17
Continued from the preceding page.
Temperature
Cycle
Humidity Steady
State
Humidity Load
Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T2.5%
(Whichever is
larger)
30pF min. : QU1000
30pF max. :
C:Nominal
More than 10,000MΩ or 500Ω
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T5%
(Whichever is
larger)
30pF and over :
10pF and over,
30pF and below:
10pF and below :
C : Nominal
More than 1,000MΩ or 50Ω
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T7.5%
(Whichever is
larger)
30pF and over :
30pF and below :
C : Nominal
More than 500MΩ or 25Ω
No failure
Compensating Type
Capacitance (pF)
Capacitance (pF)
Capacitance (pF)
Temperature
QU100+10C/3
QU275+5C/2
or T0.25pF
QU400+20C
or T0.75pF
QU200+10C
or T0.5pF
QU350
QU200
R7, R6 : Within T7.5%
R7, R6 : Within T12.5%
R7, R6 : Within T12.5%
R7, R6
R7, R6
R7, R6
Char.
Char.
Char.
Specifications
•
F (Whichever is smaller)
•
F (Whichever is smaller)
25V min.
•
25V min.
25V min.
0.025
max.
F (Whichever is smaller)
max.
0.05
max.
0.05
High Dielectric Type
0.035
max.
16V
max.
max.
0.05
0.05
16V
16V
0.035
max.
10V
10V/6.3V
10V/6.3V
max.
max.
0.05
0.05
max.
6.3V
0.05
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10). Perform the five cycles
according to the four heat treatments listed in the following
table. Let sit for 24T2 hours (temperature compensating type)
or 48T4 hours (high dielectric constant type) at room
temperature, then measure.
• Initial measurement for high dielectric constant type
Sit the capacitor at 40T2°C and 90 to 95% humidity for 500T12
hours.
Remove and let sit for 24T2 hours (temperature compensating
type) or 48T4 hours (high dielectric constant type) at room
temperature, then measure.
Apply the rated voltage at 40T2°C and 90 to 95% humidity for
500T12 hours.
Remove and let sit for 24T2 hours(temperature compensating
type) or 48T4 hours (high dielectric constant type) at room
temprature, then muasure.
The charge/discharge current is less than 50mA.
Perform a heat treatment at 150+0/-10°C for one hour and
then let sit for 48T4 hours at room temperature.
Perform the initial measurement.
Temp. (°C)
Time (min.)
Step
Temp. +0/–3
Operating
30±3
Min.
1
Test Method
Temp.
Room
2 to 3
Continued on the following page.
2
Temp. +3/–0
Operating
30±3
Max.
3
Temp.
Room
2 to 3
4