PV36Y103C01B00 Murata, PV36Y103C01B00 Datasheet - Page 32

• Manufacturer Part Number: PV36Y103C01B00
• Description: Trimmer Resistors - Multi Turn 10Kohms 10mm Square 25turn
• Manufacturer: Murata

Specifications of PV36Y103C01B00

• Resistance: 10 KOhms
• Power Rating: 0.5 Watt (1/2 Watt)
• Operating Temperature Range: - 55 C to + 125 C
• Element Type: Cermet
• Product: Multi-Turn Trimmer Potentiometers
• Tolerance: 10 %
• Number Of Turns: 25
• Taper: Linear
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
(1) Can be soldered by reflow soldering method, flow
(2) Use our standard land dimension. Excessive land
(3) Standard soldering condition
(4) Apply the appropriate amount of solder paste.
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P.R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
soldering method, and soldering iron. (In case
of flow soldering, it is necessary to clean
after soldering.)
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(a) Reflow and flow soldering :
(b) Soldering iron:
Before using other soldering conditions than
those listed above, please consult with a Murata
factory representative prior to using. If the
soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the trimmer potentiometer may deviate from the
specified characteristics.
The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the
dimension of land pattern used should be Murata's
standard land pattern at reflow soldering.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
>Temperature of tip 400 deg.C max.
>Soldering time
>Diameter
>Wattage of iron
Refer to the standard temperature profile.
2mm dia. max.
5 sec. max.
40W max.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(5) The soldering iron should not come in contact
(1) Do not apply excessive force (preferably 9.8N
(2) Do not warp and/or bend PC board to prevent
(3) In chip placers, the recommended size of the
(1) Isopropyl alcohol and Ethyl alcohol are
(2) The following are the recommended cleaning
the following environmental conditions:
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
(Ref.; 1kgf) max.), when the trimmer
potentiometer is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 4.0mm dia. and inner dimension 2.0mm
dia.
available materials for cleaning.
For other materials, please consult with a Murata
factory representative prior to using.
conditions for the potentiometer. If this part
is cleanied under any other conditions than
these listed below, the sealing construction may
be damaged.
(Condition)
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
Type1: Cold dipping/Max. 5 min.
PVM4 Series Notice
Continued on the following page.
R50E13.pdf 04.6.11
31
5